Find a sockets and switches installation professional near you

Removal of plug sockets from the wood panel, replacing them into the plywood wall, potential fix to the wall

Need some power, light and stove switches replaced

Need a licensed electrician to replace 3 light switches, 3 double power points and 1 bathroom batten light fitting. I have already purchased all the replacement fittings. Please install them and test that everything is working properly. Photos attached

Need some cables running in kitchen for new power sockets On the image, the Red is existing power The left hand corner is where the mains power for the cooker is which will need running behind to where the new cooker placement is going. I’ll need power new slot which is the green section and there is another PowerPoint below at the bottom of the kitchen the back which will be used for the cooktop but currently doesn’t seem to be given off any power.

Three bedrooms in our home previously had ceiling fans installed. The fan speed controller has been wired correctly; however, the bedroom light switches were not rewired from the original wall switch to the new switch on the fan controller. I’m looking for a licensed electrician to rewire the lighting in all three bedrooms so the light is controlled from the new fan/light switch panel instead of the old switch. Each room has the same setup, so it should be the same job repeated three times. The successful Airtasker must be a licensed electrician and hold appropriate insurance. Please include your licence details when making an offer.

I'm looking to add 2-3 power sockets along the wall in the photo towards the bottom. Currently the only power points are next to the antenna and ethernet point. All these are behind the frame on the wall in the attached photo.

Need a licensed electrician to replace a failing switch in my toilet and split it into 2 separate switches (one for the light, one for the exhaust fan). The Problem Single switch currently controls both the ceiling light and the fan. When I turn it on, it sparks visibly, then works. Turn it off and on again quickly — nothing happens. Leave it off for 2 hours — works again (with another spark). Pattern is getting worse. Already tested: ✅ Fan works fine on a separate power point (motor is healthy) ✅ Light works fine on its own ✅ Breaker is NOT tripping ✅ One nearby room's light goes off with the toilet when it fails — shared circuit Conclusion: the switch itself is failing (worn contacts / loose terminals from fan startup inrush). What I need done: Replace existing 1-gang switch with a 2-gang switch plate (light on one, fan on the other) Inspect the wall box for heat damage and flag anything concerning Confirm wiring supports the split before doing extra work Quote should include the 2-gang switch and faceplate (or tell me what to buy).

I need my two old Belkin wemo light switches changed over to a new model. I have the new ones and need someone to install them.

Installing of 4 wall power sockets and setting up tv on the wall with hidden wires ,12 down lights installed in living and kitchen area

Screw in 3 light switches 1 power point 1 light

Replace existing light switch making a buzzing sound in the light fixture

I have purchased new light switches and power points for the whole house. I just need someone to install them all.

Some of the switches on the left side of the house not working. These are the plug points on the walls.

Need to repair/replace three Classic 2 Gang Switch and one PowerPoint Double GPO switch

I need a Qualified Electrician to provide and install 3 light in my flats and fixed one light switch please. You need to provide tax receipt or invoices. Photo attached

Looking for an electrician to complete a small residential job in my apartment. The apartment was built around 2000, so the wiring is relatively modern and I don’t anticipate any major issues. Work required: Light switches and power points + two LED lights replaced, includes - * Replace 11 × double power points * Replace 1 × quad power point * Replace 6 × single light switches * Replace 1 × two gang light switch * Install 2 × two gang LED dimmer/switch combinations * Might need 1 × surface mounting block (bathroom) * Install 2 × new Martec Fino LED ceiling lights, replacing two existing LED ceiling lights (same locations, pretty much the same lights just a bit bigger, no new wiring required ect) I will supply everything, it’s Clipsal Iconic and I think the old ones are HMP: * Clipsal Iconic switches and power points * Martec Fino LED lights * Dimmers * Mounting block I’m looking for: * Licensed and insured electrician * Neat, professional installation * Experience installing Clipsal Iconic products and LED dimmers Preferred, not necessary though Photos of the existing switches, power points and lights can be provided if needed

Description: Looking for a fully licensed electrician to replace existing light switches with LED-compatible dimmers across four zones. The job requires: 1. Kitchen & Living Room: Replace a 2-gang (double) switch sitting between the rooms. Both the kitchen and living room lights are on 3-way circuits (controlled by two different switches). I want this double switch converted to a double-dimmer plate. The secondary switches for these rooms will remain standard. 2. Bedrooms: Replace standard single switches in two separate bedrooms with standard single dimmer switches. Bulbs: ​The existing downlights are dimmable Domus BOOST-10-WHT units. Switches: Current faceplate sizes are about 117mm x 72mm Requirements: - Must be a licensed electrician and provide your license number in your offer. - Electrical Safety Certificate must be issued upon completion. - Please include the cost of all 4 LED compatible dimmer mechanisms (preferable matching current switch style and of good quality like Clipsal Iconic or HPM) and new faceplates (or explicitly detail material costs in your offer). Thank you!

Electrician Required – Replace & Install Power Points & Light Switches (Single-Level Home) Scope: Looking for a licensed electrician for the following: -New double power points = 6 -Replace single power points = 4 -Replace double power points = 10 -Replace triple power point = 1 -Replace quad light switch = 1 -Single PP replaced with double PP = 1 -Replace standard single light switches = 4 -Replace single dimmer light switches = 3 -Relocate triple light switch = 1 -Relocate double power point = 1 Single-level home. Easy access with driveway parking. Power on. All work to comply with Australian Standards. Please quote your total price including labour, materials, fittings. Happy to answer any questions or provide further photos/floor plan.

Need a licensed electrician in Sydney to adjust wiring for ceiling fan/light switches. Currently there are two switches: 1. Low light 2. Main light + ceiling fan together I’d like it changed so that the fan is linked to the low light instead. Main light still needs to work properly. Please quote including callout/labour.

Need qualified Electrician to: 2 x replace existing 4 gang mechanical switch to new 4 gang smart switches 2 x replace existing 6 gang mechanical switch to new 4 gang smart switches 1 x replace existing 3 gang mechanical switch to new 4 gang smart switches 1 x replace existing 1 gang mechanical switch to new 2 gang smart switches 2 x replace existing 2 gang mechanical switch to new 2 gang smart switches 7 x replace existing 1 gang mechanical switch to new 1 gang smart switches Switches I have purchased: https://amzn.asia/d/0eCM9VSb https://amzn.asia/d/0dQzODls https://amzn.asia/d/0gJdQbvq Install a recessed plug - to mount a magnetic plate for iPad as per: https://community.home-assistant.io/t/floating-ipad-dashboard-wall-mount-that-is-charging-magnetic-and-detachable/956322 I have purchased: https://kuxiu.co/products/kuxiu-x39-pro-max?variant=46232839356468 and looking to mount.