Find a professional gate installation in South West Perth

I am after someone to fix the gates, I am posting on behalf of my Dad who suffers dementia.

Melville council requests that my pool gate direction be switched to open out (from presently opening in), The gate is fixed to concrete pillars.

Part of recent pool inspection, our gate should only swing outwards. Can anyone help with this? Can negotiate budget on work done.

I have a 3.4 meter driveway I'd like to install swing auto gates. Would require supply and install.

Remove the old electric gate and controller that does not work as well as the sensors.

Need gate to be reprogrammed. Was working fine, circuit card was hard reset when trying to pair key remotes. Supply all tools and specialised equipment. Reprogram gate. Pair remotes to gate. Thanks in advance. Craig

Looking for an experienced fencing installer to complete a small boundary fence installation out front of our new house. What I already have: • 5 steel fence panels (2200mm x 1200mm) • 1 Bunnings gate What I need from you: • Inspect/assess and tell me what additional materials are required (posts, post caps, post mix, brackets, screws, hinges, etc.) • I will purchase all extra materials • Once materials are onsite, install the 5 panels and gate to a professional standard • Cut panels to fit if required • Ensure posts are straight, aligned and secure • Hang gate correctly with proper clearances and smooth operation Requirements: • Demonstrated fencing installation experience • Must bring all tools (grinder, drill, post hole tools, level, etc.) • Attention to detail

Need to replace this gate with colorbond gate. This gate is 4m wide. I need double opening gate ~1.5m wide each. And one fixed panel ~1m wide. Gate with double sided lock and self closing hinges. I invite offers to supply and install everything required for this task. Thanks.

I need help to set up a gate to prevent my dog from going outside, any makeshift solutions are welcome. Thank you in advance

Install 15m of colorbond fencing with 2 1m gates

Glass pool gate not self-closibg even when hinges are tightened

We need a timber side gate custom built to fit the driveway. About 2m tall and 2.5m wide. Needs to be lockable from behind. Also needs a hole to put car charging cable through at times.

Task Completed / Work Summary: Assembled and installed the Perma Extra Tall Baby Gate with 20 cm extensions. Built the dog potty base frame, laid and secured the turf. Can also supply high-quality, dog-friendly turf if needed for future jobs. Ensured all parts were fitted securely, level, and ready for use.

I need to install a pool gate

I need a colour bond gate made and installed in a pre existing fence. Height is approx 1.8 m and gate needs to be 900-1000 wide. Needs to include posts hinges and latch

The side gate supports have come lose and the fixings need replacing and the gate realigned

My Centsys D5 Evo sliding gate opens normally but won’t close. The control panel shows “Safety Beam Active.” The gate was recently derailed and has since been put back on track. Looking for someone experienced with Centurion/Centsys gate motors to inspect and fix the issue.

I need a gate installation on the side of my house

Reweld gate hinge to post

Redoing the brick paving to accommodate the newly installed gate track. Need to raise level so that car won’t impact track when it drives over it. I started the job to replace one side up to the newly installed gate track and whilst I think I did a decent job on the first side I think someone else will be able to do the other side quicker and better than me! May seek an opinion on whether first side has been done sufficiently and consider getting it redone In summary - Pull back a couple more rows of bricks on side that needs the most raising (so that there isn’t a steep ramp) - Add and spread sand (I have 2.5 bags which is hopefully enough but maybe some other base also recommended) to raise level up to above gate track (allowing for settling) and level with other side - Compact - Re-lay bricks with original pattern -Fill cracks with paving sand (I have 1.5bags) This is for labour only but if other products recommended will purchase. It is my best guess based on how long the first side took me on assumption someone with experience in paving and right equipment will be able to do it in 2-3hrs but open to negotiation on that or paying more if it turns out to be a bigger job than I’ve explained