Find a professional fitness equipment installer in Brisbane

I am needing a home gym assembled.

I need someone to set up my pre owned home gym that was dissembled by its previous owner

I need a handyman to install a wall and floor-mounted gym rack which has a chin-up bar on it and to remove our old chin-up bar from the wall. The floor is concrete, so we need to drill dyna bolts into the ground, and the wall is a hollow fibre cement wall that will need reinforcing behind it with timber bolted to a besser block wall. It's not a difficult job, but we'll need someone with some carpentry skills. In the photos: - The white chin-up bar is what needs to be removed from the wall. - The black gym rack is what we need installed. - The photo of the tiles is the ground where the dyna bolts need to be drilled into. We have all the equipment and bolts and everything that needs to be installed. You ned to bring a hammer drill and any other tools that you may need.

I need to finish assembling a Major Fitness B52 all-in-one home gym Smith Machine in a spare room in a house. The frame is 3/4 finished. The job will involve the following steps: https://cdn.shopify.com/s/files/1/0580/4484/2041/files/B52_manual.pdf?v=1731987480 1. Move treadmill from other downstairs room into new gym room (note this needs to fit through a narrow door space (0.8m) so some of it may need to be dismantled and reassembled 2. Full assembly of the all-in-one unit including attaching weight stack, cables, pulleys and all accessories. Should take around 2-3 hours based on supplier estimate Instructions for the assembly are here:

I need someone to assemble a Major Fitness B52 all-in-one home gym Smith Machine in a spare room in a house. The job will involve the following steps: 1. Move double door ikea wardrobe out of gym room into other bedroom 2. Move treadmill from other downstairs room into new gym room (note this needs to fit through a narrow door space (0.8m) so some of it may need to be dismantled and reassembled 3. Move all the boxes and equipment and a few small bits of furniture from under the front of house into the gym room. 4. Lay down single gym mat flooring into room under space where smith machine will be set up 5. Full assembly of the all-in-one unit including attaching weight stack, cables, pulleys and all accessories. Should take around 2-3 hours based on supplier estimate Instructions for the assembly are here: https://cdn.shopify.com/s/files/1/0580/4484/2041/files/B52_manual.pdf?v=1731987480

Looking for someone to Assemble gym equipment. Experience preferred. Picture attached. Job is in Nundah, Brisbane.

I need to assemble a Sumo Strength Cable Cell Evolve Functional Trainer in a single garage at a house. The job will involve the following steps: 1. Moving all the boxes and equipment and a few small bits of furniture outside of the garage 2. Brief clean of the floor inside the garage. It is an epoxy coated flooring so likely a 5 minute sweep, 5 minute mop, we will provide our cleaning equipment 3. Lay down 1m x 1m rubber tiles matting through the garage. Leave these unfixed. Will need to cut some tiles in half to fill the space. 4. Assemble the main gym equipment 5. Set up the accessories including weight plates, and attachments, neatly inside the garage Instructions for the assembly are here: https://manuals.plus/evolve/sumo-strength-cable-cell-evolve-functional-trainer-manual

Assembly of a leg press. Instructions are provided but experience would be recommended. 45 degree leg press, tools provided if needed. Need done soon

I need to have 2 old sanitary dispensers removed and replaced with two brand-new ones. They’re currently stuck onto the wall which needs to be removed and then the new ones need to be screwed in.

Assemble x2 gym equipment

Hi there, I’m looking for someone experienced to assemble: • Concept2 RowErg • Concept2 BikeErg • Force USA 3 Tier Dumbbell Rack All are brand new in boxes. Assembly instructions are included in the box. Would ideally like someone who has assembled gym equipment before and has their own tools. Located in Bulimba 4171. Thank you.

Assembly growplay compact monkey bars, climbing frame and swing set

Building flatpack gym equipment at my home

I’m chasing someone who is able to repair/ replace a snapped cable on a leg curl machine. It’s a healthstream leg curl/ leg extension machine. Located in Newstead

I want to install a Gymnastics ladder and pole in our apartment. the problem is both the wall and ceiling are drywall and I don't know if the studs behind it can support the weight. do you have any experience about this to help me with that? Pole: https://www.dance4me.com.au/x-pert-nxn-removable-spinning-pole-set/ Swedish Ladder: https://www.amazon.com.au/gp/product/B0FFM9Y5RN/ref=ewc_pr_img_2?smid=A2QO0QAJ0QKPED&psc=1

We will be building this bathroom around 3 m deep and 5 m wide which will have two separate entrance points for a male shower toilet and a female shower toilet. You’ll have an offsider while you are here and you’ll need to sign off on the works. We will be able to cut in the floor waste points before you begin. Site visit is required before accepting any offer. We will purchase materials outside of the budget

I tried to install the gym equipment but failed , I need someone to fix it

Assemble a Kids Playground from Lifespan kids on grassed area of house. Currently in 3 flat pack boxes + slide Manual link below: https://share.lifespanonline.com.au/manuals/Kids%20Manual/LSK_Manual_Orangutan%20Play%20Centre_Digital.pdf

Need help assembling a home gym. It's an all in one gym with smith machine.

-Make up weights rack - make up cortex SM25 with all attachments - make up revel 4 person sauna