Find a fence installation professional in Sydney Eastern Suburbs

Replacing an existing side fence (anpprox 18 meters long x 600 high) and front gate (1.8 high x 1 meter wide)) with aluminium.

Hello, I’m looking for a new garden gate that has a lock and provides privacy. Our current gate is too low, with easy access for people to enter the garden. The old gate will need taking away. We need the gate with lock providing and installation.

See pics & description please

I need an outdoor lock to be installed. I will need you to buy the appropriate lock as well. Happy to pay cash for the lock when you come. Just check with price to make sure not too expensive. As long as it locks from outside.

Need a gate installed in the side passageway similar to the one shown in the picture At the other end.

Need a temporary pool fence that I can keep for summer and remove in winter and then put back up next year. I have a fence solution in mind and would like to discuss this with the successful trade person. Person must have tools including a drill that can go through brick and concrete. Please do NOT apply if you are not fluent with this task. I am assuming it will take 6 hours. Happy to agree an hourly rate if it goes over this cost. Ideally get this done next weekend. I would like to order them fence materials this weekend so ideally need to have an hourly rate with you, on site, to chat through the solution with you. Happy to pay for this hour on site immediately and that is separate to the air Tasker cost for this task.

Gate post needs to be reset to brick wall. The bolts securing the post are half out of the wall they are bent, and need to be removed and replaced in the process of resetting the post to brick wall to enable gate to open and close.

The supporting wood needs to be replaced. Area is approximately 1 meter by 5 meters.

We’re looking to close the gaps under our 4.4 m Colorbond fence and garden gate to stop rats getting through and prevent our puppy escaping. We're looking at istalling a galvanised vermin mesh barrier under the fence (cut into strips and bent into an L-shape), fixed to the bottom rail and buried under cinder blocks along the fence line. For the gate, we’re thinking about adding a metal kick plate plus a flexible brush strip underneath to seal any uneven gaps while still allowing the gate to swing freely. We’ll supply materials (mesh, fixings, cinder blocks, kick plate, brush strip).

Install landscaping wire along fences, for climbing jasmine plants. Length of fence is approximately 30m. We can supply the hardware or you can, but it must match the existing hardware (stainless steel as shown in photos) and receipts must be provided for all items purchased.

Remove aluminium gate post (rusted at base) and supply and fit new post and concrete into ground, Reattach gate. Post is "surfmist" color. Easy access

Hello, I'm looking for quotes to supply and install a pedestrian gate and small fence between our concrete wall posts. Preferably looking for aluminium/colourbond slat gate and fence in colourbond woodland grey colour. Please see below for measurements but I would be keen for the measurements to be done by yourself in case these are not quite accurate. Please quote price. Gate space is 99cm width 133cm Height Fence is 74cm height 175cm width

My old blockwork fence fell over in the wind last night. You probably need to chip off the old mortar and relay the blocks. It is about 3metres long and 1.8m high. You could do the entire fence for alot more if you are good.

I need black fencing with a small gate - see photos - fence 4300mm in length to join from existing colourbond fence to the garage wall. Something similar to pool fencing would be sufficient.

Replace old pine fence with 7.7metre, 1.8m high pine paling & gal steel posts (embedded in quick set concrete)

Install 17m of Outdoor Panels on existing timber fence: 1. Remove lightweight white corrugated fence covers. 2. Supply and Install any required joists on timber fence 2. Cut to size Outdoor Panels (supplied by me). Each panel is 2.9m by 200mm. https://delacopanels.com.au/products/white-outdoor-panel. The desired height is 2.4m. 3. Install Panels and a trim on top of the panels using screws. Need supply of screws (depending on joists used).

Hinges have rusted through on side gate. Hoping someone can replace hinges and rehang gate so it is functional again. Actual gate and wooden stumps appear ok.

We have just had someone pull out last minute. Looking for some help from someone experienced. Looking to add some additional privacy with fence screening (30cm to 40cm), to sit on top of the existing wall. The wall is 9 metres long. I have panels that we can re-use. 16 x 2.9m panels, plus 9 x 1.4m (plus more in the garage if needed). The wall is currently 1.3m high and then raises up to 1.6m high at end of garden. The wall is 9m long. Looking to have the fence come up to 1.8m-1.9m. The posts will need to sit on top and then the panels facing into the garden. Assuming 2 posts per height we would need a total of 12 posts installed. We don't need panels the neighbours side. The quote will need to include the brackets/posts (that will need to be cut to size). We're also looking to cover up the area marked green. Thinking using sound proof cubes from bunnings (about $50 per pack) and then some panel, that can be painted/made to line up with wall. Let me know if you have any other questions.

I have the gate already, i just need a professional installer to come install. INSTALL Only. Gate is around 1800 x 900

I need to install two fences as a barrier between units. It will require fence posts and rails to secure the fencing material to. I do not have the raw materials or tools. Measurements for each fence: - Left side: 102 inches/259cm - Right side 108 inches/274cm Height: 1.6-1.8m Two gaps where fencing needs to be fitted pictured below