Find a fence installation professional in ACT

I would like to a professional to replace a shared boundary fence with an ACT Housing dwelling. Job Specifications: Fence Type: Standard Colorbond fence Height: 1.8 metres high Length: 16 metres long Sleeper: timber Inclusions: Must include the dismantling, removal, and disposal fees of the existing old fence. Important Note: This project requires approval from Programmed / Housing ACT for a cost split. Therefore, you must be able to provide a formal, written PDF quote with a valid ABN.

Remove and replace approximately 8 meters of 1.8 high treated pine fence

Please advise on specific gate and associated hardware materials required, for me to purchase, and then install these for me. Gate width is approx 1.5m and want it to be approx 1m high

Install an aluminum gate and aluminum posts. Posts are bolt on. Posts to be installed on existing concrete (see second picture) Please note posts will need to be cut down to size. Gate is welded and ready to hang. All hardware provided. Posts are 100mm x 100mm x 2m, and gate is approx 150cm x 150cm.

Install Feature slat fences in backyard. See attached pictures of the area. There will be 7 slat fences with 13 in-ground posts. Fence sizes vary from 200 cms wide X 180 cms H to 200cmsX60cms. One double gate (100X150 each side) with a colorbond fence panel to close spaces between garage and brick wall. 4 in-ground posts required for gate and colorbond fence. We will supply all fence and gate materials. Installer to bring concrete, do the 17 post holes digging, and provide all the installation related labour. The slat fences have been supplied by Stratco Fyrshwick.

I want a courtyard fence with gates built mainly from recycled materials, about 1.2 height with metal pool fence panels or similar, I hope you procure these panels with your Ute, and put together and fix in ground, I’ll pay your time and labour, and I’ll pay separately for the materials to vendor, type of fence panels open to discussion, or wood pickets, and I I have a gate or two I hope to use, it’s not a perfectly clear area and goes over a path, but a flat block , easy access

1. Remove old palings and wooden braces of old side gate. 2. Replace with new palings and wooden braces (already purchases and stained) 3. Remove current latch. 4. Replace with new latch. Steel framework to remain W: 2620 H:1820 You are to supply nails, screws and appropriate equipment

Our trailer has been reversed into our colourbond fence and 3 panels require replacing

I’m Looking for someone with experience installing star pickets The task involves: Driving 4 star pickets (1.7m) into the ground Securing the 2 metal trellises (1.2m x 1.8m) to the pickets All materials supplied except wire Good access

My colourbond gate needs repair/ replacement. It has cracked along welds, dropped and warped. I think that maybe a pedestrian gate might stop this happening again.

I need a small wood paling or plank fence build to replace the existing one. It is approximately 1.2 wide and 1.4 high.

install colourbond fencing on top of timber fence. all tools and materials supplied. Ideally for someone who is close to this area and can come to inspect the task before giving me quotes. There are 3 seperate tasks and I will pay reasonably well for the right skills. 1) install colourbond fence adjacent to already existing timber fence. 2) install steel posts into soil for shade sail 3) pour concrete and level about 4m square of soil.

Remove old fence and replace with new lapped timber paling fence 1800h by approximately 16m long.

I will supply the materials. You just need to install.

I need a to install a gate in the wooden laneway fence that runs down the side of my property. This will be to fit a trailer into my yard. I’ve attached 3 photos - one from inside the property (with the compost bin) and two from the laneway (with the pile of mulch.) I'm looking for quotes that do not include materials as I can arrange material separately.

Looking for an experienced installer to supply and install a Colorbond side gate and panel for side access of house including lokklatch. • Total opening width: 1.5 metres • Posts to be either concreted or securely bolted to slab • Height approx 1.5–1.8m (open to recommendation) • Must be level, secure and neatly finished

Rebooking task between Niamh and Brad

- Remove existing timber fence - take away all rubbish - install 1.8m by 33m color bond fence. - The site will be ready for the fencing project from the 15th of March 2026. - Photos are not available right now.

Looking for an experienced installer to supply and install a tubular steel fence with a gate to replace this temp fencing i have. approximately 2.5 metres wide total. Details: Tubular steel fencing (black powder-coated preferred) Include one gate within the fence section Standard residential height (around 1.2 m, open to suggestions) Total width: ~2.5 m Install in ground + concrete as per photo. Flexible on timing — looking for a clean, solid installation.

I need vertical fence like pool fence with a gate . Total length is 3 meter including the gate. Please quote for the supply and install. Thanks.