Find a local electronics repairer in Sydney Eastern Suburbs

Replace washers on shower taps. Plumbers only please.

Fix hair straightener that is no longer switching on

Ghd straightener will no longer switch on

I purchase adhesive DIY vinyl tiles and contact paper for kitchen floors and cabinets as well as bathroom floors. I need assistance with laying the vinyl from someone with more experience than me! My kitchen and bathroom and pictured. They are both quite small so it wouldn’t take more than 4-5 hours. I plan to just do the Kitchen countertops and floor, then just bathroom floor.

I bought a Simpson washing machine (ezi sensor swf10761) from FB marketplace and in transit the drain hose tore. I bought a new drain hose and attempted to replace this myself but I can’t get the drain hose out of the washing machine. It doesn’t look like the side panels can be removed either but not sure. I just need help replacing the hose. It will probably be a very quick job for someone that knows what they are doing. The hose tore where it enters the washing machine. You can see in the first image, I cut it to pull it out but it just won’t come out. The second image is the new hose.

I require the removal of existing handrails and the supply and installation of four new, highly stable handrails for either side of two sets of outdoor steps (five steps per set). The current rails are screwed directly into the steps and are unstable. The new rails must be set into concrete (either core-drilled into existing substrate or set in new concrete footings) to ensure they are solid and do not rely on screws into brick. Specifications: Height: The top of the handrail must be between 865mm and 1000mm measured vertically from the stair nosing. The height must be consistent throughout the flight. Grip: The handrail must have a circular cross-section with an external diameter of 30mm to 50mm to allow for a full "power grip." Continuity: The rail should, where possible, extend at least one tread depth beyond the top and bottom risers. Scope of work: Remove 4x existing timber handrails fixed to brick. Supply and install 4x new handrails (Treated Timber or Galvanised/Powder-coated Metal). Anchor all posts directly into concrete for maximum stability. Ensure all surfaces where old rails were removed are left neat, flush, and safe. Requirements for Applicants: You must have experience with structural handrail installations. Please provide photos of previous work with an address of a prior installation in the local (Randwick council) area that I can drive to inspect the quality and stability. Tools: bring your own.

Assemble a toddler bed, move a cot upstairs and disassemble cardboard packaging

I need install two new heating lamps in our bathrooms. The ceiling is drywall so there’s a need to cut it and make sure the new lamps fit.

Change washers on dripping taps: shower head and bathroom sink tap.

When we ran our washing machine, it started tripping the electricity fuse . We opened the fuse but it continued to trip the fuse so we shut the washing machine. We have a Samsung washing machine

Currently vanity is 600mm with a dual tap. Needs to be removed. Pipes then need to be converted to be suitable for a mixer tap. Then need to install a 750mm vanity with the new mixer tap.

1 have 1 cubic metre of wood chips in our driveway. I need them moved to our back garden and spread on the flowerbeds.

Repair two steps which have separated Easy access to behind stairs

Just general touch-ups on paint. Majority of it is black. It would be good if we can have someone that can look at the paint, match it and touch up the area. We no longer have the paint available and we don't know what we used.

Just need the circuit board for my standing desk re-soldered. I tripped over the cord and screwed it up. I unsoldered it and cleaned it up, but it’s too finicky for my amateur self to put back together because there isn’t a lot of wire left, and it needs to go through the back of the plastic unit that holds the circuit board (see picture 2).

I’m looking for a qualified plumber to replace my shower taps, and also add more plumbing tape to my shower head (it’s a little leaky). Please see pics for current taps. Below is a link to the quarter pins I’m replacing the taps with. https://www.bunnings.com.au/mondella-chrome-resonance-1-4-turn-pin-lever-wall-top-assembly_p0683916

Drill and secure 2 wheel stops into concrete garage floor . 3 mounting spikes provided should

I’m starting a kitchen and laundry renovation and qualified plumber to cut off water to the existing sinks and taps disconnected. No new fixtures need installing yet — just need everything safely capped and ready for the renovation work. This includes a kitchen and a laundry + reverse osmosis tank system.

We are looking for some electrical work in the house. Replacing wall switches and HVAC with smart ones, adding in heat lamps to the bathrooms and wiring in some lights. Setup is all manual switches and oldish HVAC system. Looking to make it smart using my connected Home Assistant and ZigBee setup. 1. Replace 15-20x wall switches with Zigbee-compatible smart dimmer switches/modules (mix of lighting, vents, towel heaters). Something like this https://amzn.asia/d/hDYa4GD 2. Install 3x Honeywell T6 Pro thermostats for HVAC zones. 3. Convert 3x front outdoor lights to motion or light-sensor control (still manually overridable via Home Assistant). 4. Wire 2 x accent lights above paintings to existing circuits. 5. Add bathroom heat lamp control (two bathrooms) ideally integrated with existing switches 6. Add USB-C / USB-A combo outlets: One on each side of the master bed. 7. Add new powerpoints: Porch Side of house (for outdoor use, weatherproof) Below or behind TV (for hidden cabling and media gear). 8. Add house number light with outdoor-rated low-wattage LED (ideally connected to photo sensor or schedule). Share quote for job or you might need to do a site visit first if need more info.

Install: 3 Tile Change 4 taps 1 shower 1 faucet in same bath