Find a local electronics repairer in Bondi Junction

I need a carpenter with an industrial electric tool or one that will work to put screws through what appears to be a mental door frame to hang a pull up bar. If you have done something like this before that would be great or have the right tool for the job it won’t work with hand help tools. Should only take 5-10 minutes max with the right tool.

I’m looking for a licensed electrician to complete the electrical installation of a large AOKE cardboard cutting plotter. The machine has two Redbo regenerative vacuum pumps (2.2kW each, 220–240V single phase) that connect through the supplied electrical control box. The control box needs to be hardwired into the building’s electrical supply and the system tested to ensure everything operates correctly. Scope of work: * Inspect the supplied equipment. * Hardwire the supplied electrical control box. * Connect and commission the two vacuum pumps. * Verify correct operation of the machine. * Ensure installation complies with Australian electrical standards. * Advise if any additional circuit protection or electrical work is required. Equipment details: * AOKE cardboard cutting plotter * 2 × Redbo regenerative vacuum pumps * Single phase 220–240V * 2.2kW (13.7A) per pump * Electrical control box supplied I’ve attached photos of: * The vacuum pumps * The pump specification plate * The supplied electrical control box Please only respond if you’re a licensed electrician with experience installing commercial or industrial equipment. If you’ve worked with CNC machines, routers, laser cutters, vacuum pumps or similar machinery, please mention that in your offer.

Need two sets of basin taps changed to a mixer , One set already have stop valves , the other to have valves fitted during change And one bidet toilet seat fitted (needs pipe put in line) I have already bought the new mixers and plugs for holes, and the 2 valves Also have the bidet and kit , just needs the valve put in line off the existing flexable hose

Removed taps and cap pipes so wall is flush

Need 2x table tops as per pic and dimensions as per specs attached. I have table bases from supplier (that is readily available), but need the tops done. Note custom size of 600-700.

Apply gap filler to stop cold draughts between dark wooden floor boards and white skirting boards or wall. Must be done neatly and professionally, someone with attention to detail. It’s a typical sized terrace house, the area in question is kitchen, dining and TV area on the ground floor. We would prefer people quote me their hourly rate as it’s hers to know exactly how long it will take to do the job properly. We will purchase the necessary filler (eg. Coloured Sellys no more gaps and foam backing rod just in case)

2 GHDs. Both don't turn on. One has a plate that has been slightly detached for a while yet it was working fine.

2 year old console. HDMI port has failed. Have tried different cables. I can supply the correct fitting if you tell me what to get.

Please see pic attached 2 induction electric on left currently not working which has one small on top and bigger one at bottom total dimension 510x 285mm currently have fan issue hence not working perhaps electric board faulty required to replace ?? . Any parts in for repairs ?

My old pads are worn out and needs to be changed with new ones

Two ceiling fans, and three pendant lights need to replace old ceiling lights in my rental unit. It is on the top (3rd) floor of 30s apartment block. Can use access to roof space through ceiling in fire escape if needed.

Hi there, We need a licensed electrician to inspect a switchboard issue at a residential property tomorrow. One of the switches on the switchboard keeps tripping — we reset it, but it immediately flips back down. Some power is still working in the apartment, but one section is without electricity. This could be a blown fuse or another underlying power issue. We’re looking for someone who can identify the cause and carry out the necessary repair. Please bring appropriate tools and let us know your availability for tomorrow. Thanks

MY GHD hair straightener keeps showing a red light and making a weird noise. It doesn't heat up anymore either.

There are a few paint chips in the wall from a lamp and headboard stoppers. Will require paint as there is no spare paint.

I need a licensed electrician to diagnose and fix a circuit breaker that keeps tripping in my home. The issue seems to be with one of the circuits in my switchboard, which includes power for various appliances. Task Details: Inspect the switchboard and identify the cause of the recurring tripping. Check for potential overload, short circuit, or faulty wiring. Test connected appliances and outlets if necessary. Ensure the circuit is safe and functional after repairs.

My ghd hair straightener is not working. It seems like the thermostat is faulty and needs repair.

Replace my 2x ceiling lamps with owners’ lamps due to house move

I'm looking for an experienced handyman or tradesperson to help fix cracking cornices on my roof and address dirt infiltration issues. I have the wall colour paint if required.

The light is flashing red and they are making a beeping noise. Online it says it could be thermostat

I need to install 2 x 20 amps plugs the premises already have 3 phase power.