Find trusted local electricians in Mornington VIC

Electrician to install a light, the cord is already there for it. Electrician please - and will need a ladder

Remove two fluro lights and replace with warm led - prefer if you can supply them. Install is in Mornington Let me know your quote Thanks

Remove bedroom fan/light. Disconnect dishwasher, disconnect outside cameras

Ethernet point and power point installation from existing point to new point in bedroom Single storey and tile roof

Qualified Electrician Needed – Disconnect & Cap Off Sauna (Quick Job) Description: Looking for a licensed electrician to disconnect and safely cap off power to a sauna unit on my balcony. The job is very straightforward: • Isolate and disconnect power to the sauna heater • Safely cap off the wiring • Ensure everything is left compliant and safe The sauna is easily accessible and already installed (see photos). Power runs externally into the unit, so access is simple. Requirements: • Must be a qualified/licensed electrician • Own tools • Able to ensure safe and compliant disconnection Timing: • Need this done by tomorrow (flexible on exact time) Location: Mornington Should be a quick in-and-out job for the right person.

I need an experienced tradesperson to correctly prepare existing electrical conduits that currently sit on top of the crushed rock base, so the area is ready for concrete pouring. Works required: • Carefully lift and lower existing PVC electrical conduits so they sit below the finished concrete slab level • Provide proper sand or fine crusher dust bedding under the conduits (no sharp aggregate) • Ensure minimum 50–75mm clearance below the concrete slab • Cover conduits with sand (minimum 50mm) before re-instating crushed rock • Re-level and compact the crushed rock base to a clean, even finish suitable for concreting • Ensure conduits are protected from crushing and movement (sleeving if required) Important notes: • This is a driveway slab area and will carry vehicle loads • Conduits must not be visible at finished base level • Work must comply with standard pre-concrete construction practice • Area must be ready for immediate concrete pour once complete

We have a pallet of old solar panels and aluminium mounting along with some disposable stuff to collect and remove from the roadside. Can be repurposed/recycled The whole lot needs to be taken

Need 1 outdoor power point installing and also another in the eaves outside for a plug in ceiling speaker. Existing power is 1-2 metres away in both locations

I need a qualified person to rewire three ceiling light fittings so they can be safely plugged into a standard Australian 3-pin power point. -Two of the lights currently have US plugs attached -One has no plug at all -You will need to supply new Australian plugs, cords, and any necessary fittings -I’m happy to drop the lights off and pick them up once the work is complete (Melbourne or nearby suburbs) -Please ensure the work is safe and fully compliant with Australian electrical standards.

Dig trench for electrical 13 metres approx through gravel driveway in Mornington

I have 9 x older style LED down lights that I want to replace with more modern dished style Downlights. I also one failed modern Downlight that I have a new driver for but need fitted. Can I get a quote please to do the above 10 lights. Also how much more would it cost to fit them off with switchless gpo’s for easy future replacement.

See pics for my requirements plus 2 outdoor Brick lights. SUMMARY:- 4 new powerpoints , 3 powerpoints relocated very close to original position and 2x External Lights with add on switch inside the house. The LED mirrors to be installed.

Need certificate of safety for power to be turned on

New power point installed in a cupboard and change over a light in bathroom

Scope of Work: Installation of a 25A circuit for a Revel Sauna Project Details: Electrical Circuit: A new dedicated 25A circuit to be installed from the main switchboard in the lounge-room to the sauna location on the balcony next to the lounge room Isolation Switch: An external isolation switch to be installed outside. Positioned at an accessible height for operation. Cable Routing: A small 25mm hole to be drilled through the exterior ceiling. Cabling will be routed down through the hole to connect to the isolation switch. From the isolation switch, wiring will run to the sauna unit inside the property. Safety Considerations: Compliance with AS/NZS 3000 wiring regulations. Appropriate weatherproofing for external components. Secure cable management to avoid hazards. Drawing Details: A detailed, to-scale electrical plan is attached, showing: Location of Main Switchboard Routing of the 25A Circuit Placement of the Isolation Switch on an External Bracket Exact Drilling Point for 25mm Hole in the Ceiling Final Connection to the Sauna Unit. It should take less than 1 hour and 45 minutes to climb up into the man hole in the bedroom, drill a 25mm hole, run cable to the sauna. The switchboard is 7 meters from the balcony and sauna. i’m an unable to do it as i’m not a qualified sparky yet A drawing is included to illustrate the electrical layout and installation requirements.

• 1 power point to move in laundry • 1 power point in cupboad • 2 power points for LED light Mirrors (1 x Ensuite & 1 bathroom) • 1 power point in Pantry • 1 power point in Ensuite to possibly be moved • 1 power point in Bathroom to possibly move Please quote for whole job or give me your hourly & approx hours you think will take

I have purchased a SOLT 60cm oven from The Good Guys in Mornington. Model GGSO605MS I need it installed in a rental property I own. The current one we are pretty sure is hard wired, the new one is 10 amp.

New home. NBN is working but only with router plugged directly into NBN box which is in garage. Socket located in lounge not working, so therefore internet only works at front of the house.

The excavator scrapped over the cable and ripped it in our front garden. Need to fix this today.

Our balcony light has fallen with recent winds (has been hanging there for over a year). Needs to be re-hung.