Find trusted local electricians in Brisbane City CBD

Looking for electrician to replace the existing chandiliya from the ceiling. 2 chandiliya small one connect to electricity Media sinnage Plug to timer

Need to replace plugs i already got the plugs only 2 plugs

Install kitchen cabinet door. Install a solar light which requires part installation on the roof. Install rac in the laundry

We have a GENTRAX GTX4200 Inverter Generator that recently won't start. We have been using it for maybe half a year. We have already tried replacing the spark plug (which was already replaced around a month ago - so might not be the issue). We reached out to the warranty provider and they suggested carburetor cleaning. We have been given instructions and attempted but could not progress far enough to take it out. Will include a picture. Alternatively, there is a chance we have added too much fuel and 'flooded' the carburetor (from researching online). We don't purposely tilt it but we are parked on an inclination. This was the video demonstration provided to the warranty provider so might as well attach it, if it helps https://streamable.com/4f2i4y **Update** Unscrewed the carby bowl to drain the fuel. Also did the spark plug test for ignition/spark (with it disconnected). Managed the get the generator running for about 30 seconds. However when starting it, it felt different than when it works properly. Choke position out, two pulls, almost seems like it will go but doesn't. Immediate tried choke position in and pull and it runs. After about 10s there will be unusual 'putt' noises before the red signal and it turns itself off, along with a last puff of smoke and bad smell. We have sprayed 'Start ya bastard' - removed the bowl and sprayed into that entrance. Choke position out, 1st pull, seemed to almost start, pushed the choke in and it started to run. but again, for only 30s with similar observations. We are in Chapel Hill, but we are able to come to you with the generator and also flexible with the time (including evening).

Looking for a licensed and CEC-accredited electrician for solar panel and battery installation in Brisbane and Ipswich Qld 4305

Replace my old power points with these new evo-charge powerpoints. Please quote for supply and install.

Electricity box trips and part of the apartment does not have any power (kitchen area). On outlet in the kitchen area causes the box to trip

We’re looking for a licensed commercial electrician to assist with the electrical fit-out of our new office located in Brisbane CBD. Scope includes: • Installing power outlets (including floor boxes) as per the electrical plan • Wiring for workstations, boardroom, and common areas • Ensuring compliance with Australian standards and electrical codes Plans have already been prepared by our designer and approved by our engineer. Please refer to the attached drawing for the detailed layout and specifications.

Looking for someone to Rough in 10 x power points + 2 x data points. Should be ready next Friday.

There is no power socket in this room however there is light. I need to install a power point in this room. Thanks

I need some to install a dishwasher in my kitchen. It needs to be fully installed so requires a plumber etc

I need a smart lock installed and a few light switches (5 in total - some of the switches connect with a fan)

Switchboard Relocation required in building in George St. Disconnect incoming feed and make safe for temporary works. Supply and replace the existing switchboard for a water proof enclosure to allow for extending all cables to the new location. Supply and extend each circuit with submersible joiners to future proof the installation and replace the existing main switch for a 160amp chassis main switch. supply and install a 48pole chassis switchboard on the stairwell platform to remove for the currant damp location. To surface mount all extended circuits into the new switchboard location and extend incoming mains from the existing location to the new location. To supply and replace all water damage safety switches to match the new board installation. To run a full installation / commissioning test as per section 8 of the AS3000 to comply to current standards.

Supply and replace 2 x 150mm exhaust fans (e.g., Ventair VMFIL150) in both bathrooms (Airflow specification of 430 m3/hr) Supply and replace 5 x 90mm LED down lights throughout the apartment Please share a time and materials breakdown.

Need 32 x Downlights installed, single story.

Hello, We are a reputable eye care and health care company urgently seeking a qualified electrician to address an electrical issue at our QLD - Albert St store. Issue: Water damage is causing an electrical short circuit. A switch has flipped, and when flipped back on, it causes a short circuit after approximately 2 minutes. This is affecting track lights, overhead lights, and potentially the lightbox. We are seeking an experienced electrician to: - Assess the water damage's impact on the electrical circuit. - Identify and repair the source of the short circuit. - Ensure the safety and proper functioning of the lighting systems. Upon receiving your assessment and offer, we aim to promptly proceed with the necessary repairs. Please note that we do not provide any materials for this maintenance task. Photos showing the water damage and affected areas are attached to this job post. Address: 136 Queen St, Brisbane City QLD 4000 (exact location will be provided once the task is assigned). We need an experienced electrician who: + Is fully licensed and insured. + Has good reviews and a high resolution rate. + Has their own equipment and tools to complete the task. + Has experience dealing with water-damaged electrical systems. If you are interested, kindly provide the following information with your offer: 1. Availability (Date and Time): Note: Due to the urgency of the situation, please indicate your earliest availability. 2. Work Scope (detailed steps you will take to resolve the issue): 3. Offer fee (including material and labor fee): Thank you very much for your attention to this job post.

Broken batten at the base of the Table lamp to be repaired /replaced

I have ordered a letter sign with back lit lighting and need someone to i stall it onto concreate wall. I have a hand drill if required other equipment should be at hand.

Swap approx 30 existing power points for Clipsal lconic power points. (supplied by customer)

Vintage lamp requires rewiring