Find experienced local carpenters in Parramatta

We have an ikea kitchen that we were getting assembled and installed. The guy finished half the job and disappeared. The kitchen is assembled but needs to have the remainder installed including doors etc. We urgently need someone to come and complete the job so we can move in. We also have a bathroom cabinet that needs mild alternations. We’re based in Constitution Hill. Grateful if you can send through a quote or come look at it.

I put some clips on wall and when removing those clips, wall paint has come off and left some stains. Need to fix that and paint it.

Outdoor length about 1 metre. Nothing fancy simple and economical.

Vanity set, three seperate boxes. Reviews say takes time to put together . Instructions provided and can be emailed across to view prior

Please obtain the wood yourself and construct wooden boxes as shown in the image. Each wooden box should have a total height of 1 meter, divided into two equally sized vertical sections and four equally sized horizontal sections, creating a total of eight square compartments per box. I will need a total of 8 sets of these boxes. Reference images are attached

Hi, I’m replacing my stair rails with glass and need some carpentry work done.

Hi, We have an outdoor decking area and we want to install the 3 power boards so that we can use laptop or connect heating appliance etc. You need to supply the materials.

I need this timber frame taken down (see picture) and replaced with new timber frame. Same size and dimensions. Please quote for dismantle and replace. Do not include in your quote disposal of old timber or to re-paint. Thank you.

I have FIVE decorative wall panels that need to be installed in an office setting. Prefer the job to be done ASAP. - Each panel is 2700mm (H) * 600mm (W). I need somebody to mount them onto a plasterboard wall, forming effectively a single 2700mm (H) * 3000mm (W) feature wall. - You WILL need to bring some kind of circular saw to trim panels. The wall is about 2880mm wide, but the five panels together make 3000mm. The right-most panel will need to be trimmed horizontally to fit. -Each panel is 2700mm high, but floor to ceiling appears to be 2680mm by my measurement. It is possible that each panel will also need to top/bottom shaved by about 20mm to make it fit. I am not entirely sure if I just measured incorrectly. - The backing of each panel is an acoustic flexible felt material. Each panel will need a minimum of NINE black plasterboard screws (3.5mm * 25-35mm) through the felt, and into the wall. - The far left panel needs to be trimmed at a corner to accommodate for a skirting that is 160mm high and protrudes from the wall by about 30mm. This blocks that left panel from reaching the floor.

I needed some extra storage so bought a small wheelie bin shed. ABSCO BIN COVER 1508WCK. Need someone to assemble. Located in an apartment basement. Neighbouring car spot empty so can be used to build there. I will also move my car before you arrive.

Multiple small reno work to be done. 1. Removing old Aircon box and bricklay hole and internal plaster board (no painting required and already have bricks ready to lay). 2. Kitchen entrance door frame 3. Kitchen to living room opening frame 4. Gaps in between kitchen cabinets to be covered 5. Dishwasher installed properly in between cabinets 6. Skylight frame to be added and fixed

- Installation of 2 Doors for Walk-in-wardrobe - Installation of Additional Shelves and Drawers We will pay for the doors. Doors have not been purchased yet.

https://www.landera.com.au/garden-sheds-structures/plastic-garden-sheds/lifetime-sheds/lifetime-tool-store-19mx11m-3047-litres/ Need the above lifetime shed assembled

Ceiling on the dining area requires painting to address the water stained marks. Would require someone to select the appropriate color of the pre- existing walls and paint the water stained marks

Please see attached pictures of completed cupboard with planks. The other one has just one Plank built, I would like to have 6 more planks to be installed, I have necessary planks, they just need to be cut to below dimensions (in mm) & drill into the wall. I will have markings on the walls where they need to be installed. Need to bring circular saw/equivalent tool to cut to size & driller kit to drill into the wall, Max 2 hours job as some planks are already cut to size. Resting Plank (885 × 595 × 16) Supporting Planks 1 & 2 that go on the side (600 × 70 × 16) Supporting Plank 3 that goes at the rear (885 × 70 × 16)

Need a professional stratco shed installer Picture attached of the garden shed Needs to have experience Wentworthville

Taken down old pendant lights and replace with stain glass pendants. One in kitchen area. One in hall way. Ladder required. Home during most days.

Made-to-measure shelves (three) for a broom cupboard

New laminate with join to be installed, I have ordered new benchtop, i require install and cut out for sink only, please see photos

The benchtop cutouts need to be cut by 3-5 cms just from 1 side (front). See the red line - only that side bench needs the cut. Have to remove the small wooden plank connected at bottom.