Find a reliable cooktop installation and repair service in QLD

Remove existing electric hob Install new electric hob Neighbour has installed the same Nightingale 60cm hob model and it fits

Installation by Electrician Run new 6mm cable from switchboard to PowerPoint adjacent cookercavity. Remove and replace current double gpo and and install a double gpo with an extra switch to allow for a 32amp isolation switch to be installed. Run 6mm cable from isolation switch to the cooker cavity and connect new cooker. Replace current 20Amp cb and install a new 32amp Type A RCBO to comply with Australian wiring standards. Test and commission install. Materials: 6mm cable, 32amp RCBO, 32 isolation switch, double gpo with an extra switch, junction box, corro, screws and fixings.

Replace cooktop with new one I have already bought, need licensed electrician. Looking for offers get it done before 20th

I need an experienced stonemason to install a marble benchtop and cut out the cooktop and sink area, I will have the necessary people to help carry it during installation.

Looking for someone to help us remove and replaced our electric cooktop and oven and install electrical isolator switch

Need new gas top cooker connected to exisiting connection. Has been installed to bench top (although can lift up for access if needed) the pipe from the cooktop and the main in let is only 300mm away from each other. We are on tank supply (LPG)

Renovating my kitchen and need a licensed plumber and gasfitter to: - Disconnect kitchen sink hot & cold water and cap off safely - Disconnect sink waste and seal the pipe - Disconnect gas cooktop and cap off the gas line Requirements: - Must hold BOTH a QBCC plumbing licence and a Queensland gas work licence (please include both numbers in your offer) - Gas compliance certificate supplied for the gas work A separate fee/task will be arranged to reconnect everything once the new benchtop is in. Photos of the sink cupboard and cooktop attached. Located near Beenleigh. Flexible on timing.

Replace gas cooktop with a new one. New cooktop is already purchased and the exact same model

We need our old cracked glass cooktop taken out and new one installed. Qualified electrician only please. We have new cooktop ready to be installed, should be plug and play. Offers please for the next week sometime. Thanks

Needing electrical work for a kitchen from a licensed professional. Looking to have induction cook top and oven installed as well as addition of around 8 power points including 1 external point. Also needing bathroom light/extractor installed

I am replacing my electric cooktop for a difrent model and need an electrician to reconnect it

We have bought a secondhand oven and just need a hand to pull out and replace the old oven. Standard 60cm oven. Pretty flexible on times. No need to take away old oven, just to pull out and install the new (pictured)

Looking for an appropriately qualified/licensed appliance repairer or gas fitter to attend a short-term rental property in Windsor, Brisbane to diagnose and repair a gas cooktop ignition issue. Issue: - Gas is flowing to the burners normally - Burners are not electronically sparking/igniting - Guests can currently light the burners manually, but we need the ignition repaired - Make/model can be provided once confirmed We would like someone to attend as soon as possible this week, diagnose the fault and repair it where possible during the same attendance. Potential issue may relate to the ignition system, spark module, electrode or microswitch, however this will need to be professionally diagnosed. Please include in your offer: - Call-out/diagnostic fee - Your availability - Relevant licence/qualifications - Whether you can supply common replacement parts if required Please provide photos/details of the fault and completed repair for our property records.

Electrician required to install new cooktop and oven.

I’m looking for a licensed electrician for a small job at my rental property in Clontarf next Wednesday, 7 October. There are two jobs to complete: - Remove the existing electric cooktop and install a new replacement cooktop - Replace a faulty/intermittent light switch I’ll purchase and supply the new cooktop and switch beforehand, so I’m really just looking for someone to handle the electrical installation and connection. I’ll be at the property at the same time doing a few minor maintenance jobs, so access is easy and there’s no need to coordinate separately with the tenant once the time is locked in. The cooktop is being replaced rather than repaired, so I’m not looking for fault-finding on the appliance itself — just removal of the old unit and installation of the new one. Ideally looking for someone who: - Is a properly licensed electrician - Can complete both jobs in the same visit - Is available Wednesday 7 October - Can provide the appropriate electrical safety/compliance documentation Clontarf QLD 4019. Please include your availability and labour price when responding. Happy to send photos/details of the existing cooktop and switch before the job if helpful.

Ceramic Cooktop Replacement — Runcorn My 60cm electric ceramic cooktop cracked and need replacing the whole thing, i bought a new unit just need someone with the right license to do the below, work order required. - Remove and dispose the old/broken cooktop (take it away) - Fit new replacement unit, reconnect & test 📍 Runcorn, Brisbane 🕐 2 Sep, before 2pm 🚗 Easy parking & access Need licensed/insured quote. Please include cost + confirm the time. Thanks!

Getting a new oven and need some assistance replacing the old one. My budget is not a hard and fast limit. Make me an offer.

To fit new cook top above oven.

Looking for a qualified electrician/appliance installer to disconnect and remove an old cooktop, then install a new Devanti 60cm Electric Ceramic Cooktop with Touch Control. Scope of work: Disconnect and remove the existing cooktop from the benchtop cutout Leave the removed unit on-site, I will dispose of it myself Install the new Devanti 60cm Electric Ceramic Cooktop (Touch Control model) Connect to existing electrical wiring/circuit Fit into existing benchtop cutout Test all touch controls and heating zones for correct operation Ensure unit is secure, sealed, and level