Find experienced local carpenters in Yatala SA

Replace an old rotting beam. Appro. 5000 x 150 x 45mm at the end of a sloped pergola. Require collection and installation of new beam and removal of old beam. Check soundness of pergola roofing, may require rebolting or screwing.

Fixing the fridge upper & side cabinet to make space for bigger fridge.

We have 13 shelves that need to be unpacked and put together then put into position.

Hi, I’m looking for someone experienced to install a commercial stainless steel bench. Bench size is approximately 5900mm long x 2500mm wide (modular stainless setup) to be installed in a plaster/production room. Location: Salisbury area Access is good and plans can be provided. Ideally someone with commercial fit-out or stainless installation experience. Just installed in the plaster room Looking to get this installed soon. Please message me if interested or if you’d like to come past and have a look.

Wanting to freshen up the cladding on outdoor bbq wanting to remove it and do it with something like spotted gum battens

I need a temporary partition stud wall built in my two car garage in my modern two story townhouse. I want it to divide the area into 2 separate areas with a lockable hung door. I'm wanting it to be secure for storage but also fairly temporary so it can be dismantled easy down the track if I choose to. It doesn't go floor to ceiling but rather 5.5m long x 2.3m high as a partition only. There is no insulation required and can be cladded on one side only with something similar to ply wood.

Need to have old dated kitchen doors replaced. I have one replaced already, when you come and checking sizing etc you can see what it looks like (purchased at bunnings). The budget is a place holder until its been quoted by you. The quote to include supply of the doors, you can use the door handles from the existing doors as they've been replaced recently

Forgot to mention, i need the existing wardrobe to be removed too. I have 2 IKEA wardrobes that need to be secured to the wall, and I need the skirting to be cut so the back sit flush against the wall. And I need a couple of overhead cabinets to be installed in laundry room

Re staining of entry timber door to match current stain. Inside, outside including side panel.

Need old wooden cupboard to be lined with mdf/or something & shelves replaced. Measures: 1.9m wide x 1.75 h. Put an amount in to post the ad but have no idea of cost.

Either paint it or replace the wooden strips

To install built in wardrobe

The cabinets installed in our kitchen need some minor trim detailing done for a final polished look.

Please quote for wood rot in post and beam of verandah, also bottom of a garage door. I will have a painter finish the job. Budget flexible as I’m insure of the scope of work. Thank you!

Installation of a two door base cabinet to a tiled wall, with solid brick behind the tiles. Also cut and install the bench top

Hello, My name is Avin and I’m looking to get some work done in my kitchen. I need the old fridge space converted into a cupboard with a door and shelves, and I also need a couple of drawers installed in the adjacent area. I’ve attached a photo for reference, the area marked in red is for the cupboard and the area marked in blue is for the drawers. I’m located in Kilkenny.

I have a corner door in kitchen cabinet that have hinges broken off. I have tried fixing but it’s quite old and the previous drill holes and plugs that have been removed are badly damaged. Previous drill holes on the cabinet and doors will need to be done again somehow as I’ve done a shiet job attempting myself. I have already bought what I think it’s the right hinge, a 165 degree one and the other one. Both doors approx 720mm by 350mm.

IKEA Nysjön cabinet needs to be fixed to wall. Must go in front of some plumbing so may need some old timber or similar to use as chocks. Furniture is already assembled to the point where it needs to be affixed.

I have a small kitchen with no space to install dishwasher. currently sits in the space meant for the fridge. I have no idea how to best approach the problem and have included as many photos as possible to help show the dilemma. Please let me know if you need any further information. Hoping to be able to rework existing setup and not spend too much money as my budget is limited. Thank you for helping.

I’ve just purchased a Billy bookcase (160mm x 28cm x 202cm), and would like it built. I also need some skirting board cut so that bookshelf can sit flush against the wall and the anti-tipping can be installed (skirting board will prevent this).