Find an experienced cabinet maker in NSW

Supply & install Laundry Cabinets 1500mm X 580mm + wall hung cabinets, stone top

Having trouble building a bar/counter on wheels. I have started the project I just need help finishing it. So someone with some building or cabinet experience would be great!

I need a warped shelf from a leaky air conditioner on the book shelf (just one )replaced. The laundry cabinet has some issues that need fixing too!! Budget can be increased as needed

Fridge wont fit but need to remove one side to allow the fridge to go in. Need a carpenter or cabinet maker.

Looking to build custom cabinets specifications attached we are open to quote as we are not experts to budget it

Our slide out bin broke. Need a cabinet maker/joiner to install the new Euro Cargo Bin we have purchased (see photo). We'd like our existing cabinet door attached.

Looking for a cabinet maker to craft a bathroom cupboard with mirror doors Tiles are setting but roughly 1800x790x140

I want to add dishwasher to my cabinet by removing a part of it.

Licensed experienced cabinet, skirting/ceiling trim builder required to finish off a small kitchen in Redfern. Four cabinet doors and two drawer faces need to be fitted that includes reworking the frames a little. Also there’s about eight metres of kickboard trim that needs to be angled around doors and stairs. Materials onsite. Just need your skills, tools and the pride you show in your work. You will be in and out in less than a day. Need someone who demonstrates they have pride in their work. Level access, 10 metres from the kerb. Price quoted includes all your out of pockets. Job would suit an experienced retiree looking for the odd day’s work.

Installer cabinet maker required on site to fit, scribe install cabinetry panels/fillers. Work will be per hour once compete, with potential for other days to complete. Must be accurate/competent with electric plane to scribe panels, fillers and desks.

Best to have a chat ! Cabinet is 90% done - needs some finishing touches with some woodwork pieces left.

the current Drawer NEEDS to be LINED with an INNER Shell to cut-around the 50mm Plumbing Waste-pipe. - please see the pics- .. pic.1 is the current Drawer. .. pic.2 . is an example of the CUT-OUT for the Pipe - BUT, it does not need to be this big. I have some Materials - ply - that can be used for this. ... you will NEED to- (1) CUT strips of approximately 70mm high and screw these to the Drawer frame / to each other. (2)CUT a base that needs to be glued to the existing base. any questions.? - pls ask..

I have installed a dishwasher in our kitchen which required shortening one of the modules to fit. This was a corner module with a hinged double corner door which needs to have one panel of the door cut and rejoined to fit the narrower section. This will need to be taken out of the centre due to the decorative boarder and also the hinge insets. Can deliver the panel almost anywhere Newcastle/Hunter as I travel daily for work.

We require a shoe stand to be built out of timber or the likes. It must be retractable. Please refer to pics. I do have the panel for the door, but a handle will be required. The dimensions are- base -980mm, height-750mm, top- 1233mm

I keep glueing the corner back with liquid nails but it doesn’t stay glued because of the water and steam from the dishwasher. I need a cabinet makers to fix it for good. Thanks

Looking for a cabinet maker to create two timber sliding doors in here.

Existing dishwasher pictures and measurement attached. Replacing current drawer type dishwasher (Width 895mm) with free-standing Miele dishwasher (Width 600mm). Model G7604 Built Under SC Front AutoDos. Pictures attached - both the unit name and installation dimensions requirement. 1. Take out the existing dishwasher. 2. Prep the area for ‘Built-under’ Dishwasher 600mm width - picture attached the new DW model, dimensions requirements. This requires building an internal wall/panel so the new DW can be bolted on. 3. Trim/Cut from existing dishwasher door panel to fill the gap from (existing dishwasher width is 895mm minus new one width 600mm = 295mm width trim) **No need to install the new DW** Just need to prep the area so it’s ready to install by Miele technician.

I have a kitchen that is being done by a cabinet maker He has suggested I get full set of drawings for what I have in mind I know the design that I’m after I need someone that can draw up what I want for cabinet maker I’m not exactly sure how much this should cost so I’m starting here at this price

Measure current cabinets and replace with new ones in black

Kitchen guy has done a runner with our drawer front so need a replacement panel made for front of drawer front. Runner is Titus. Colour is Bayleaf. Have offcuts to match paint.