Find skilled builders in Glen Waverley

I am renovating a 1970s brick veneer house. The architectural plans have already been prepared by a licensed architect. I now require structural engineering drawings and details for building surveyor approval and for the builder to execute the works. The proposed works include: Opening the living room to the kitchen by removing an internal non load bearing wall. Expanding the laundry and dry kitchen area by removing/modifying existing brick walls, which are understood to be load bearing. Providing structural design and drawings for any required beams, lintels, posts, pad footings, connection details and load transfer requirements. Providing documentation suitable for building permit approval by the building surveyor. Providing construction details clear enough for the builder to price and carry out the work. The house is a 1970s brick veneer construction, so the structural assessment should consider existing roof loads, ceiling framing, wall load paths, brickwork, foundations and any temporary propping requirements during construction. Please review the architectural drawings and advise: Whether a site inspection is required. What structural drawings and computations you will provide. Your fee and timeframe. Whether the drawings will be suitable for both surveyor approval and builder execution. Has to be licenced engineer

Would like to install flu for woodfire heater

Hey just wanting an approx quote regarding doing a deck in my backyard. I'm wanting to put a sauna on and possible spa in the future so it may need some reinforcement?? It's approx 1650x3700.

Need exposed aggregate concreting done for my driveway. 100mm thick with steel reinforcements and expansion cuts. The driveway will need to be acid washed and sealed as well. Approximate 50 square metres. It is a flat land. Pls provide quote.

Need carpenter to replace rot fascia of house on ground floor. Approximate length 13 linear meters. Will supply timber of treated pine. Attached are the photographs.

I need to install a standard power point for my pergolas (within the red circle of the photo). The pergolas has wiring for lighting already. I need licensed electrician to do the job.

Cutting back plants and digging out overgrown plants - View all the details of this offer: https://www.airtasker.com/offers/01KBCADANXTDNEVBW3S5JMDVWE

Looking to build pergola over porch area as per plan attached

The post is shorter than other ones, which causes leaks when raining.

A 6m x3m easy shed new one Need help with assembly

Shed assembly. The size is 3* 3 metres.

2 x freestanding louvered pergolas need to be built and installed onto a decked area

I need a carpenter to fix my pergola. Please see attached photos

install absco regent 3mx1.44mx2.3m garden shed. Slab is ready. Parts have been delivered. Just need to put it up

Concrete driveway is lifting due to tree roots. We need the concrete to be smashed and evened

I need to Architectural drawings for 1.5 meter high bricks fence rendered with concrete caping painted and iron infill. Sample attached.

paint walkway and driveway I don’t have the paint Also, I can not measure the place as I am not at home. There are also some cracks on the walkway to fix. If you want to supply the material, that's ok, or I can pay the material fees, but you need give me the quote. Thank you!

I have a painted concrete driveway, the paint on it was fading, 2 years ago I had it repainted. Unfortunately, the person who did it did a horrible job on it, less than a week after the job was done the paint has peeling off in a lot of places and it is very slippery. I need to have it fix while we are still in summer.

Require the disassembly and transportation of insulated roofing sheets. Each roofing sheet is approx 3.2m long by 1m wide, with 8 sheets altogether. There are associated post and roof support beams as well. Once disassembled, i can arrange transportation. Must be suitably experienced to safely remove sheets without damage.

Previous shed building experience essential. The Task: Assemble a 3m x 1.5 gabled Easyshed. This is a standard product with everything provided. Variations to the standard product include the Portal Frame kit and 2 x skylight roofing sheets. Full build documentation provided. Ladder available. Tasker to provide own equipment and PPE. Tools required: Power Drill and batteries, Phillips Head driver/s, step ladder, drill bits: 3mm steel, 6mm steel, 10 mm steel, measuring tape and string line. Safety gloves and glasses mandatory. Pop-rivet tool provided. OUT OF SCOPE: Locking down shed into brickwork