Hire a trusted appliance repair service in Willoughby NSW

I need a qualified carpenter, cabinet maker, or experienced kitchen installer to fix a poorly installed rangehood in my kitchen. An electrician has already run the wiring and connected the unit, but the physical positioning is incorrect. The job requires: 1. Unmounting the current rangehood. 2. Modifying the internal cabinet carcass: The back panel/spacer needs to be removed/shaved down so that the cupboard doors can close fully and flush. 3. Lowering the rangehood to the correct, safe height. 4. Remounting the rangehood perfectly level and secure. Please only offer if you have the proper cabinetry tools to cleanly cut the cupboard backing without splintering the laminate/timber finish. Pictures attached. Thank you.

Getting an error code : 1E on screen from an LG front loader washing machine, need to have it looked and repaired

Washing machine door needs to fix

need to repair our gas fireplace which has stopped working. Manual is below. Business we brought it through is no operating. Neither the remote or the manual button on the fireplace will turn on the pilot light. think it might be an ignition problem. https://www.manualslib.com/manual/763347/Real-Fires-Flameboyant-Rf800-Pearl-Flameboyant-Rf800-Minimal-Flameboyant-Rf800-Modern-Flameboyant-Rf800-Classic.html?page=14#

Treadmill (Everfit TMILL-CHI-420-M6-WH) is experiencing ongoing belt and motor issues. The belt slips or stops completely when weight is applied, even at the lowest speed. Error code E-2 appeared initially, which indicates a motor or speed sensor fault. After adjusting the belt tension, error E-0 appears, but the issue persists. Belt has been correctly lubricated and tensioned per instructions. Issue appears to relate to motor power delivery, speed sensor, or drive system.

My Treadmill (Everfit TMILL-CHI-420-M6-WH) is experiencing ongoing belt and motor issues. The belt slips or stops completely when weight is applied, even at the lowest speed. Error code E-2 appeared initially, which indicates a motor or speed sensor fault. After adjusting the belt tension, error E-0 appears, but the issue persists. Belt has been correctly lubricated and tensioned per instructions. Issue appears to relate to motor power delivery, speed sensor, or drive system.

The fridge is screaming when compressor fan spinning

The cable on my Nov 2023 new Ryobi 18V 37 cm mower (model no R18XLMW24) has been accidentally cut through, so there is no connection between on switch and motor. The cable needs replacing. Ryobi will not fix this and Bunnings will not cover under warranty.

Hi - we installed a motorised awning and the cassette/gear mechanism at the end broke apart as we began retracting it. The motor itself is fine - looking to just repair/replace the housing if possible. - Due date: Flexible

The irrigation system has stopped working - I need someone to fix it - Due date: Flexible

I require help replacing the rubber gasket that seals the door of a washing machine (model number LG WV9-1412W). I got a new gasket from the manufacturer, and attempted to do it myself. But I don't have the spring expansioning tool to complete the task. If you could help with that, much appreciated. Thanks. - Due date: Before Sunday, 24 September 2023

Heat pump dryer won’t spin - Due date: Needs to be done on Tuesday, 15 August 2023

Unable to remove the filter from the washing machine - Due date: Needs to be done on Friday, 17 February 2023

Lawn mower needs repair. Blowing smoke when running. Petrol / oil seeping out the side where the filter is - Due date: Flexible

Pump working , but water not getting thru - likely a leak on the roof - Due date: Flexible

My dryer is making a loud banging noise when in use. I think it is the bearings. I was wondering if anyone out there can fix it? thanks Amanda - Due date: Needs to be done on Friday, 7 October 2022