Find a professional aluminum fence installer in NSW

Seeking quotes to replace aluminium fence in bad condition and install bollards or another suggested method externally and internally so that cars do not continue to impact them and damage them. Please quote. Photo attached

Looking for an experienced fencing installer to install aluminium fence posts only. Fence panels and gates will be installed separately later. The fencing system is pre-manufactured and DIY-friendly. Posts are already supplied pre-cut to the required sizes, so no general cutting is required. Only a few posts may need minor trimming on site due to the slope/fall of the land to achieve the correct finished height. Work required: * Accurately measure and set out fence/post positions and boundaries. * Maintain exact spacing so the supplied fence panels and gates fit correctly later. * Dig approximately 23 post holes – 600mm deep. * Install and concrete aluminium posts. * 3 additional posts require drilling/fixing into existing concrete. * Ensure all posts are straight, plumb, correctly spaced and aligned. * Minor trimming of a few posts if required due to changing ground levels. * Clean up after completion. Materials supplied: * Black powder-coated 6063-T5 aluminium posts. * Standard posts: 65 × 65 × 2mm. * Most posts are 1.8m long. * A few are 2.0m long to accommodate the sloping ground. * Larger gate posts: 150 × 150 × 3mm. * Concrete bags will be supplied by me. Important: This job is for POST INSTALLATION ONLY. No fence panel or gate installation is required. Installer should have fencing experience and own post-hole digging/drilling equipment, levels and an aluminium saw for minor trimming. Please provide a fixed labour-only price for the complete post installation.

Looking for an experienced fencing installer to install a black aluminium slat fence and gates. Scope of work: * Mark fence line and ensure boundaries are straight and accurate. * Dig 23 post holes (600 mm deep). * Install aluminium fence panels and gates. * Concrete all inground posts. * Core drill 3 posts into existing concrete. * Cut aluminium posts to the correct height where required (bring your own aluminium cutting/drop saw). * Ensure gates are aligned, level, and operate smoothly. * Clean up the site after completion. Materials supplied: * Aluminium fence panels, posts, gates, screws, and accessories. * Concrete bags. You need to bring: * Post hole digger/auger. * Core drilling equipment. * Aluminium cutting saw. * All standard fencing tools and PPE. Requirements: * Proven experience installing aluminium/slat fencing. * Ability to accurately set out fence lines and levels. * Own tools and transport. * Please include photos of previous fencing work in your offer. Looking for someone who has done similar aluminium fence installations before and can complete the job to a high standard.

Need new aluminium fence panels supply and install looking for a lighter wood spray coated finish or white . 21 panels with sizes below looking for vertical slats to go between rendered brick posts. Front Fences 2009w x 806h 2009w x 806h 3005w x 806h 2500w x 805h 2500w x 805h 2503w x 804h 2500w x 804h 2304w x 805h 2304.5 x 805h Pool fences 1605w x 1106h 2308.5w x 1106h 1602w x 1106h 1500w x 1106h 1501w x 1106h 1806w x 1106h 1805w x 1106h 1806w x 1106h Side passage 1806w x 1005h 1808w x 1005h 1805.5w x 1005h 2101.5 x 1005h

We have an old timber boundary fence that needs to be pulled down and replaced with a new aluminium boundary fence 6 m x 750 height And must have all your insurance in place

We are looking for a licensed aluminium fence and gates installer only. We will supply the aluminium fence, gate, posts and all hardware required to complete the task. The aluminium blade fence material will be installed on an strip concrete footing already in place and 1 brick wall. Please see the picture for further details. I will need an invoice and the license number of the trade person/s.

Small (8m) fencing surrounding a dog wash, damaged by a car hitting it. Exisiting posts need to be removed and new posts fixed with chemset bolts. New panels to be cut to size and installed. The job is at Haberfield, Sydney, but the new panels and posts to be collected from Marrickville, Sydney.

I have all the components for the erection of a 'Protector' aluminium fence approx 5 meters, including the gate. Fixing to existing paved brick and vertical walls on each end. Each post to be secured with 4 x M8 110mm galvanised anchor studs and Chemset (we have 10mm masonry drill bits, threaded rods and chemset on site). Installer will need to ensure the sections are level as there is a slight slope on the ground. I need someone who can carry out this job as soon as possible.

1: shift an existing gate down by cutting it then welding it further down so dog can’t escape. 2: turn two exisiting fences to latch gates to allow external pool access

Small fence between brick peer and current aluminium fence. Approximately 1 metre. Powder coated aluminium.

Need someone to install Aluminium Fence in my front yard. See pics for reference

Need Aluminium fence extension (like brown one ) on top of empty concrete fence approx 8m long and 90cm high. would like like the white fence.

I’m looking for an experienced and licensed installer to install a small section of pool fencing to close the entry access from the house to the pool area for compliance purposes. I can buy the material from Bunnings Scope of work: • Install a short section of compliant pool fencing • Include a self-closing, self-latching gate (if required) • Ensure installation meets NSW pool safety compliance standards • Secure fixing to existing surfaces (to be confirmed onsite) This is a small section only, not a full pool fence.

My fence is damaged and the screws have come off and needs to either be replaced or fixed

Require 2 fence posts to be replaced and colourbond fence reinstalled, The fence posts snapped at the bases in a storm a week ago, we have purchases the posts and concrete, just don’t have the time to complete it. Work required - Exisiting concrete to be removed, - post hole to be dug deeper - new posts to be installed and concreted in - colour bond fence panel to be reinstalled

I need to side gates in front fencing going down the duplex and on the front.

Need structural steel installed for a single story house. I will supply, just need installation.

Install front aluminium fence with gate and sliding drive way plus motor

Aluminium welding broken fences

I need to move aluminium fences on top of boundary to only have 30 mils of gap