Find a reliable appliance technician in Inner South West Sydney

Garage door remote randomly stopped working. The other remote that I have works fine. Need to program a new remote

I tried to empty the water from the drain tube but it snapped back into the machine before I could put the plug back on it

My fridge just stopped working Still has power but both fridge and freezer isn’t cooling anymore would like to know what the problem is and if it can be fixed

Rangehood light needs replacing. Instead of using proprietary lights. I need it converted so it can work with lights purchased from Amazon. Need the plugs to be convert power from 240 down so led lights can be used. I have the lights already

Looking for a garage door technician to help consolidate 3 remotes (gate, garage door & turntable) into 1 remote. TURNTABLE: Elsema Penta FOB, FOB43304, 433.1 to 434.7 MHz GATE: BFT, Type B RCB 4 GARAGE DOOR: HMA-P, 433.92 MHz

Weld a stainless oven rack

Door of Bosch inbuilt microwave has come loose and needs to be fixed

Washing Machine shows E3 instantly on pressing start (likely faulty lid magnetic switch or tilt sensor)

## Licensed Gas Fitter Needed – Gas Cooktop Installation (Kogarah, NSW) I’m looking for a **licensed gas fitter with a valid NSW licence** to help install a new gas cooktop at my house in Kogarah. **Please do not apply if you do not hold the appropriate NSW gas-fitting licence.** **Preferred date:** Saturday, 17 October 2026, during the day after 12pm. **Parking:** Driveway parking available. ### Scope of Work 1. **Remove existing gas cooktop** – I can assist with removal and disposal. 2. **Install new gas cooktop** – Electrolux 60cm Natural Gas Ceramic Cooktop (Model: EHG635BE), already purchased. 3. **Enlarge existing benchtop cut-out** – The benchtop is laminate, and the existing cut-out needs to be enlarged slightly to accommodate the new cooktop. - New cut-out width: 560 mm - New cut-out depth: 490 mm I’m a qualified carpenter and can assist with the benchtop modification using a jigsaw and circular saw, if appropriate. 4. **Connect and safety-test the cooktop** – Complete the gas connection, installation and required safety testing. Existing gas and electrical outlets are available below the cooktop. ### About the Job I’m a qualified carpenter and happy to assist with suitable preparation and other tasks to help get the job done efficiently. **I don’t think the job will take too long**, especially as I can help with the removal and benchtop modification. All gas-fitting work must be completed by an appropriately licensed professional. Please get in touch if you hold the required NSW licence and are available on the preferred date. When responding, please confirm your licence, availability and quote for the job. Thank you!

We have an electric cooktop and oven that’s hard wired, we need an electrician to help remove the old wiring and install the new oven and cooktop

Need someone to install 60cm fixed range hood. No need to remove old one as it has already been taken down.

IKEA Kitchen install filler panel above PLUS Electrician to replace built-in mirowave

Hi, there are 2 out of 4 burners that currently not working as photos attached. Also the stove knob I think a bit hard to turn. We need professional to fix this

Refill a refrigerated drinks and snacks vending machine in a gym.

Hello, I have a small backyard which needs lawn mower service

Dishwasher hose to be connected waste point. The hose diameter is slightly smaller than the waste so I need a plumber to join the two properly.

For a licensed professional electrician to install four downlights in the new ceiling of our kitchen and also install an electric oven and install a double PowerPoint from the current rough in work down by another electrician

Need to connect gas oven. Also check why washing machine isn't getting water flow in.

Need someone to connect my washing machine water inlet hose to the existing laundry tap. The existing tap/connector is heavily corroded and may need to be replaced. Please supply/install the appropriate washing machine tap or adaptor if required and ensure the connection is watertight. See attached photos. Licensed plumber preferred I’m not sure what the appropriate price is for this job, so please feel free to offer what you consider reasonable for the work required

Hello, we need a handyman to remove our old fixed Rangehood (pics attached) and install our new fixed Rangehood. We need you to have all the tools and brackets etc needed. We have the new Rangehood, and it is the exact same size as the old one. If you can take the old one with you that will be even better but not necessary. This needs to be done ON Thursday 13 August, not earlier or any other date. Preferably around 11am/12pm.