Find a reliable appliance technician in Central Coast

Need a new freestanding dishwasher installed at a rental property in Berkeley Vale, NSW 2261. The new dishwasher has already been delivered to the property and will be replacing the existing dishwasher in the same location. New dishwasher: SOLT Freestanding Dishwasher Stainless Steel – GGDW6013X https://www.thegoodguys.com.au/solt-freestanding-dishwasher-stainless-steel-ggsdw6013x Job required: -Disconnect existing dishwasher -Install and connect the new dishwasher to the existing water, drainage and power connections -Level and secure the dishwasher correctly -Test it after installation to make sure there are no leaks and it is working properly -Removal/disposal of the old dishwasher would be preferred if you can provide this service, but it is not mandatory

Replace an old gas stove top ( 4 burners ) with a new one. I'll supply new Stove Top

Hi..looking for someone to install a commercial range hood just under 3m long in a pizza shop need to install and supply range hood motor..easy access ceiling is 2.7 high internal going straight up with about 1m duct out side roof is flat colorbond roof urgent job required

Haier Model: AWF80AN1 Issue: Showing E4 error after a few minutes. Initially water fills then stops and nothing happens. Doing a refresh cycle shows spinning but that's all. Tested the water pressure from tap, looks normal. Can't get around to the back of the washing machine since dryer is sitting on top and cannot lift it off.

Looking to get new washing machine placed on cabinet and installed at Copa.

Merc c200 w204 I need the blower motor taken out and one put back in

Electronics not turning machine on

Westinghouse dishwasher is displaying an F1 error. It appears the anti-flood/leak protection may have been activated. Looking for an experienced dishwasher/appliance repair technician to diagnose the cause of the leak/error and repair it. Located in Terrigal NSW 2260. Please let me know your experience with Westinghouse dishwashers. $120 budget for call-out/diagnosis and minor repair; please quote if parts or additional work are required.

Disconnect and reconnect a dual fuel oven including applying a LPG conversion kit

test and tag job for one vending machine in lake haven shopping centre. the custom phone case printing vending machine

fix two hot plates on freestanding oven

I took my cordless Dyson apart and cleaned it, put it back together and it won’t turn on. Battery is fine as the blue lights go on but just isn’t vacuuming.

Need dishwasher and washing machine setup in European laundry/kitchen. Longer hose required for washing machine to be setup to tap.

I need certified electrician to remove the existing oven and connect a new one in the kitchen

I have a professional aesthetic/beauty machine that is showing a communication error: “Connection failure between display control board and function control board.” The machine powers on and the display works, but there appears to be a communication issue between the display and main control board. I have opened the unit and can see: • Ribbon cable connection between boards • Small interface/control PCB • No obvious burn damage I suspect this may be: • Loose/damaged ribbon cable • Connector issue • Low voltage/power supply issue • Or interface board fault I am looking for someone experienced in: • Electronics repair • PCB diagnostics • Component-level repair (not just replacing whole boards) Requirements: • Experience with circuit boards / internal electronics • Ability to diagnose faults (multimeter, etc.) • Prefer someone with experience in appliances, medical or industrial equipment

I have purchased a brand new built in microwave that needs to be installed into the cavity. A piece of timber may need to be unscrewed to fit the new microwave into the cavity. My Miele dishwasher has also stopped working - it doesn’t drain properly and needs fixing.

Removed current stove top and install new induction electrical stove top

Looking for someone who can clean the cyclone unit / filter and the brush turbine head properly on a Dyson DC 54. You might call this a refurb. I would like to do it myself but I shake too much because I have Parkinsons.

I am looking for a quote to vent our range hood in the kitchen. Vent through wall, vent and duct work to be included also. I’ve included some images for reference.