Find a reliable cooktop installation and repair service in Camberwell VIC

The bottom edge banding on two overhead cabinet doors above the cooktop has warped from heat. The door faces are fine. I only want the bottom edges re edged. Do not quote to replace the doors. Scope; 1. Remove both doors, protect benchtop and splashback. 2. Cleanly cut back and remove the warped underside wrap only, leave the front face intact. 3. Prepare the underside edge, square, clean, and lightly sand for adhesion. 4. Supply and fit new plain white heat resistant ABS or PVC edge banding to the underside of both doors. Use hot melt or equivalent cabinet grade adhesive. No contact film. 5. Trim and flush both faces neatly, radius the arris lightly, seal the ends to prevent lifting, and clean any glue residue. 6. Reinstall and align the doors, check clearances to the rangehood and the neighbouring door, and confirm soft close works as before. 7. Leave the area clean Notes. • The repair is to the underside edges only. The colour can be plain white. A close white match is fine as the new edge is on the underside. • Bring 16 mm and 18 mm white edging so the job can be completed in one visit. Measure on site to confirm. • Location is an apartment kitchen near Camberwell Junction. Photos attached show the exact edges to be repaired. Onsite parking available. Requirements for the Tasker. • Cabinetmaker, shopfitter, or handyman with proven edge banding experience. • Provide a tax invoice if required. Please answer in your offer. Confirm you will re edge only, not replace the doors. Confirm you will use heat resistant ABS or PVC edging and cabinet grade hot melt or equivalent. Confirm your availability and parking needs.

Check for potential gas leaks in the cooktop.

The Miele gas cooktop is about 10mm wider and 10mm longer than the existing Blanco cooktop. The cutout needs to increase from exiting 830 x 470mm to 860 x 490 mm. Benchtop is laminate / timber.

We need to remove the old gas cooktop and install the new one .The size is 90cm.

I have a 4 burner gas hob. Originally set to natural gas but can be converted to LPG. Basically I need this cooktop converted to LPG to connect to a LCC27 gas bottle. I had purchased the wrong fittings, so I just need help to select the correct ones.

replace a gas cooktop and install a hybrid gas and induction cooktop - Due date: Flexible

Remove existing gas cooktop and instal new gas cooktop NOTE must be a licensed gas plumber - Due date: Needs to be done on Wednesday, 1 March 2023

Kitchen Reno. Need to move fuse box, install power to new oven and cooktop, dishwasher and in laundry. add in lighting x 4, - Due date: Before Friday, 23 December 2022

Installation of a Fisher & Paykel Oven and Induction cooktop. New oven / cooktop. Induction Cooktop, 4 zone, Series 9. - CI604DTB4 60cm Electric Stove, 11 Functions. Series 9 - OB60SD11PB1 Old system: Gas stove top with shut off valve. Electric oven. Double GPO at rear of oven. Joinery opening Suits oven. May require 5mm to be shaved off laminex bench top for stove top. - Due date: Flexible

A gas cook top needs to be connected to gas outlet .the outlet is in the adjacent cabinet on the wall . Please see attached pic and is shown with the red arrow . Compliance certificate is required

Replacment of current gas cook top with a new one. Should be same size but it is possible some slight cutting of caesarstone may be required. This won't be known until current one is removed. Glass splash back. - Due date: Flexible

Install a regulator to a cooktop to cpmly with Gas Safety requirement for renting property, and issue a Certificate of Compliance (we will send it to the Inspection Company). - Due date: Before Wednesday, 29th Dec 2021

Old Whirlpool cooktop used to work well but sometimes it is hard to get ignited, I reckon that is because of some parts are improperly located due to current surface clean? Try to find a plumber to give it a service and fix this issue. Photos are attached for information. - Due date: Before Friday, 17th Dec 2021