Hire trusted appliance installation services in East Melbourne

My in laws had their kitchen rangehood changed in April. Due to technical requirements the rangehood height needed to be increased from the previous rangehood and there is now a gap in between the stone splashback and underside of the rangehood. We had a custom panel made to install behind the rangehood, which will help cover the gap nicely. Original person who did the install can’t assist. Looking for a qualified person to: -Remove the rangehood -Install the custom panel in the niche -Reinstall rangehood All of the ductwork is now venting out the ceiling and has been done professionally. Looking for a tradesperson with experience working with rangehood installation, who can do this affordably. Rangehood photos and finished panel included in this post.

Remove two HPM 3-in-1 2-Lamp Instant Heat Bathroom Heater in two bathrooms, and put in two new ones purchased from retailer (probably from Bunnings, not purchased yet, open to suggestions) There are already existing exhaust pipes and wiring hooked up to the current heat lamps, will just need to remove + wire to new ones.

Our drive belt for our washing snapped. Ive bought the replacement part but cant get it on for the life of me. Need some help. Then also need a quick hand to put the dryer back on top of it. If the job could be done today or tmw would be great

Purchased a Westinghouse WRF610SA 60cm rangehood but the hole sits further back than the old rangehood so isn't just a simple straight swap. Also the current PVC is apparently a hazard so looking at different duct replaced possibly all the way to outside cowl, cover boxes inside to hide the ducting. Looking for an experienced rangehood installer/handyman to do this task

Install a new Masport Bowden Portrait wood heater under the eaves. Tiles roof. New 4M Flue kit is ready.

Converting from has stove to electric. We also need to run a new electrical wire from switch board to kitchen approx 15m. Oven brand is Technica.

Replace range hood with one identical

To be installed heat&glo fire place MODEL: 6000TRSI-AUC , frame has been built , strait out the back wall flue need to be installed and gas connected , needs to be picked up from our home and brought to site 10mins away

Holes in seal/ gasket of Miele washing machine. Have ordered a new part. Need someone to remove and reinstall. Experience in doing something like this is ideal. If not in Thursday then Saturday.

Hello, looking to install our Artusi AINT119-NF2 under counter bar fridge. Tasks are as follows: 1. Reverse the hinge so it opens from the other side as per manual. 2. Install and secure the fridge as per manual attaching it to the pictured cabinet door. 3. Re-attach the bottom ventilation panel that has been cut out in whichever way you think is best.

Removing a functioning Omega rangehood and replacing with a Westinghouse WRR604SB

Hi, looking for an electrician to replace Oven. Old one is Miele 60cm, new one is Bosch 60cm HBA572EB3A. Oven is Hardwired. Though both the models (old and new) are 60cm, I am not sure if any cabinet trimming or modification might be required, please factor that in too. Would require Certificate of Compliance. Location is Doncaster East.

Need an electrician to install Oven. I already have a new Oven, just need to take out old one and install new one. Old one is also working, so no new powerpoint would be required. Old oven can be left behind, I will discard myself

I need someone to install Smart Control on my garage so it can open and shut through a smart phone.

We have bought a Matador 4 piece barbacue and would like someone to put this together Name: Matador Ignite + 6 Burner Gas Barbecue kitchen All we want are all the pieces to be put together. No need for any plumbing/water/electrics etc. Only the actual frames to be all built.

I would like to get someone to install range hood in Burwood and take away the old one. Old and new Units are the same model

rangehood and roof kit installation, has power point, we will remove the cupboard in the middle

Need someone who can install a Rangehood with external motor. Rangehood details. Zurich 120 wide EPP motor (external - sits on roof) 800mm height Can finalise price upon inspections d discussion.

Panel for the light and fan controls has fallen off of the range hood. Needs to be re-fastened. Light and fan controls are still functional.

I would like to get someone to install range hood in two locations. Location 1 Burwood Take out the old and install the new. I have bought the range hood. Meet at 11am for this job Location 2 Elizebeth st city Take out the old and install the new. I have bought the range hood. Will come here straight after the other job in Burwood.