Hire a professional washing machine repair service in Gold Coast

LG top loader Direct drive 7.5kg washing machine not spinning. Can hear it start but sounds like it is unbalanced or come loose. Just moved house yesterday and was working fine before that. Did a load of washing earlier today and it worked but now won’t spin after trying to was towels.

HAER 7.5KG front load washing machine has FC2 fault I've drained drain pump in front, and checked filter, all looks good and clear. but still FC2 fault

Washing Machine Repair Needed Hi, I’m looking for someone who can help fix my washing machine. The rubber ring/seal is broken, but I have already purchased a new replacement ring. I just need someone experienced who can come and replace the ring for me. Please reach out if you can help or know someone who can do this job. Location: carrara Flexible timing – we can discuss what works best.

Hi, I have a F&P top loader 10kg washing machine that keeps stopping mid-cycle and constantly beeping with an “out of balance” error. I’ve already tried redistributing the clothes and different load sizes, but the issue keeps happening on fast spin. Slow spin doesn't trigger the “out of balance” error and the cycle finishes with no problems. So I believe the suspension rods may be worn and need replacing. What I need: Someone experienced with washing machine repairs Replace suspension rods. Location: Upper coomera Please include in your offer: Whether you can supply parts or if I should source and purchase them prior Trying to weigh up options of buying another machine or fix this one.

Our machine machine is leaking from somewhere. I need someone with experience to find the leak and fix it. I can see a few spots where there is some water build up. Brand is Fisher and Paykel

Electrolux front-load washing machine door hinge broken. Door not opening at all. Looking for repair or hinge replacement. Please quote including parts and labour.

New washing machine bouncing around when spinning. Needs levelling

Washing machine keeps going into error mode UB on Samsung 13kg top loader. Have to constantly re adjust load and re start. Been happening for a while

Connecting the washing machine to the water source. The valve is too hard to turn and therefore cannot connect the water. Washing machine turns on.

Servicing of Bosch Series 8 Washing Maching and dryer. Both still working, but could benefit from a checkup, clean and service.

My washing machine won’t finish the spin cycle. It seems to be a balance issue.

Error E7:00 showing and wash cycles not finishing. Looking for someone experienced fixing washing machines to come and repair. Fisher and Paykel Washsmart

1. Collection of AEG washing machine and AEG dryer from Carrara - must be able to apply anchor bolts to appliances which are supplied at pick up address. Deliver appliances to Burleigh Waters. 2. Removal of existing dryer and washing machine from Burleigh Waters - take dryer only to tip. 3. Install AEG washing machine and dryer to Burleigh Waters home *Both pick up and delivery addresses are on one level (no stairs) *Airtasker must provide protective blankets and straps for transporting appliances

Just moved in: need help connecting the washing machine hose to under the laundry sink tap. Tight spot, have been fighting with it all weekend with no success: help needed 😭🙏🏼

I have a fisher and Pike washing machine 8.5 kg, it stops every time it goes into spin mode, , I can bring it to you

Flashing 'Clean filter' but has been cleaned twice... AI says water existing slowly... no idea

Washing machine needs proper hooking up for waste water

It recently started only working on the quick cycle, and even then it sometimes stops after about 10 minutes with an error. When we try again, it usually works on the second attempt. It’s also leaking onto the floor and has become extremely loud while running. Brand: LG Model: WD13020D1

My front loader washing machine door won’t open, I’ve followed instructions on you tube still won’t open, l need someone who is knows how to fix

Renovating laundry. Need washing machine taps lowered to roughly 700mm off the ground. Will be a bench top going in so the aim is to keep the taps and hoses hidden. Pipes are copper.