Find an experienced plumber in Richmond Tweed

Cold taps are turned off tightly already but cold water keeps leaking Shower tap Bathroom sink tap

Brand new dishwasher in box. Westinghouse WSF6602XC 60cm freestanding dishwasher. Have space under sink - To RIGHT SIDE to fit in - power socket above dishwasher space/kitchen bench - on wall* *Will need to drill a hole in bench top to run power cord to socket on wall. BENCH TOP is, plastic laminate glued on top of a chipboard or particleboard. The dishwasher comes pre-fitted with the core connection lines: Water Inlet Hose: A 1.5-metre high-pressure hose featuring a 3/4" BSP female threaded connection (standard Australian garden-tap/mini-cistern size) with an integrated electronic AquaStop safety block valve at the tap end. Water Drain Hose: A 1.5-metre flexible ribbed grey drain hose with a rubber boot end ready to slide over a standard sink waste pipe spigot. I'll need to get the following from bunnings to allow for the installation job. Brasshards 2 Way Under Sink Valve 20mm x 15mm – Retrofit splitter that screws onto existing cold line to add a dedicated dishwasher tap. 3/4" BSP Male to 3/4" BSP Female Flexible Braided Hose (300mm–500mm) – Slim extension line to move the bulky AquaStop box away from the tight wall shelf. Kinetic 17 - 32mm Stainless Steel Hose Clamp – Metal clamp to tightly lock the grey drain hose onto the under-sink waste spigot. Thread Seal Teflon Tape – Essential for wrapping around bare brass threads to prevent leaks. You will need tools to fit all the above. You will need Spade Drill Bit or Hole Saw (approx. 32mm–40mm)to cut hole in sink wall and bench top/plastic laminate glued on top of a chipboard or particleboard. Let me know if I forgot anything? Thanks.

Blocked drains - plumber needed urgently. Must be familiar with septic tank systems

Electrician Needed: Convert Off-Peak Hot Water to Continuous Power I’m looking for a licensed electrician to inspect and modify my electric hot water system so it no longer relies solely on the off-peak (controlled load) tariff. The system currently only heats during the off-peak supply, and I’d like to investigate bypassing this so it can heat on a standard continuous power circuit instead. Scope of work: * Inspect the existing hot water wiring and switchboard. * Confirm whether the system can be converted from off-peak to continuous supply. * Provide and install any required wiring or circuit modifications. * Test the system and ensure everything is safe and compliant. * Advise if there are any better alternatives (such as adding a boost circuit). Property location: Mullumbimby, NSW. Please include: * Your electrical licence details. * An estimate of the total cost (or call-out fee plus hourly rate). * Any assumptions or parts that may be required. I’m looking for someone experienced with off-peak hot water systems who can recommend the most practical solution.

Looking for a full time plumber to join us! $50 - $55hr + penalty rates Genuine pathway to permanent for the right person The role kicks off ASAP with an initial 6-month contract, followed by a further 6-month extension. Prefer something more flexible? We can work with you on that. What You'll Bring Plumbing Licence (NSW) White Card + current driver's licence Solid construction plumbing experience A reliable, safety-first attitude with strong attention to detail

We have a new dishwasher arriving for delivery and installation tomorrow. But we need to have the existing dishwasher disconnected and pulled out before the delivery (the delivery and installer won't handle the disconnection). Simple job for someone who is experienced. There is only an elderly lady at the address who needs help with the disconnection.

I have a small but constant water leak coming from a valve on my main water line, just downstream of the meter (blue-capped valve – see photo). Looking for a licensed plumber to: * Inspect and confirm the source of the leak * Repair or replace the leaking valve/fitting * Ensure everything is sealed and compliant Notes: * Leak is accessible at ground level (not buried deep) * Located outdoors near the meter * Flexible timing, but sooner is better

I need to replace a broken bathroom sink with a new one I’ve already bought. I haven't been able to remove the old one, and I’m not a plumbing expert. There are tiles above the sink that I don't want to break.

Looking for a licensed plumber to help with two jobs: Bathroom: Remove the old vanity sink and taps, and install/connect the new vanity sink and taps. Kitchen: Remove the cabinet doors and kickboard, these are sitting loose to easily remove, install, and fully connect the new dishwasher (plumbing ). Photos of the old/new bathroom fixtures and the prepped kitchen cabinet space are attached. Please bring your own tools and supply any basic plumbing fittings if needed. Need to be done on specific date.

My kitchen tap is broken and I need someone to help me fix it. It still dispenses cold and hot water. Just that the tap handle is out of its position. Have a look at the images for reference.

Sink drainage need a clean and ensure there is no leaks.

Seeking to buy 1 x basin handmade copper tap: Pick up today (Friday) Install not required as my plumber is installing 7am Saturday morning.

Move water pipe (hot) copper , from in the way of the back deck and join using correct fitting for pressure.

Irritating Leaking Tap connected to Washing Machine Hot Water

Leakage on ground floor Causing mould would need a quote to ascertain cost . Could be pipes , or from upstairs kitchen . Need a quote for insurance

1. Hot water system turns off while using; investigation required and maybe upgrade 2. Leak under sink fix 3. Leak roof investigation 4. Leak outdoor pipe fix 5. Dual gas system pipe implementation

Hello, I’ve just moved house and urgently need some help with setting up washing machine.

showerheads starting to drip when off, I'm guessing it's just washers needing replaced.

I have a leaking kitchen faucet and potentially a leaking tap. Looking for a licensed plumber to check it out and fix. Please include in your offer: 1) cost for labour 2) approx cost for parts (see photos for reference)

We have installed a new sink, very basic set up We need to install the new mixer + install a water filter we purchased from Bunnings Also, the sink doesn’t line up with drain pipe Looks like it needs a new S bend installed and the pipe connected up