Find a professional gate installation in WA

Pool gate not closing properly, touching fence while closing.

After a side gate installed

TAU D749MA Rev02(11-2014) Electric double gates, one leaf won't open and close properly. I have performed a full reset, and all the appropriate lights are flashing the colour that they are supposed to. It could be a sensitivity thing, but I have tried to adjust the trimmer without success. Needs experience in gates like this to assess and repair.

Seeking a qualified and experienced fencing contractor or metal fabricator ONLY to supply, fabricate, and install a custom double swing gate. Applicants must be both qualified and experienced – no general handymen. Opening Details: Total wall-to-wall opening: 4033 mm Gate Specifications: Double swing gate (2 leaves) Each leaf approx: 1882 mm wide Overall height: 1700 mm Steel RHS frame construction Design Layout: Bottom section: 1100 mm solid infill Top section: vertical slats Slats: 65 mm wide with 50 mm gaps Approx. 15 slats per gate leaf Colour / Finish (Required): Frame: Black (powder coated) Slat inserts: Grey Council Compliance (Mandatory): Must comply with City of Wanneroo requirements Maximum 1200 mm solid from ground level Minimum 50% visibility above 1200 mm Contractor responsible for ensuring compliance Clearances: Hinge clearance: 25 mm each side Centre gap: 20 mm Bottom clearance: 50 mm from ground Scope of Work: Supply and fabrication of gates Supply and installation of: 100 mm steel posts (2 required) Heavy-duty hinges Locking system (manual latch/lock) Full installation, alignment and adjustment Budget: $3,300 total (labour and materials included)

I recently had a pool gate inspection from the council. I need something (a post, or maybe a tiny bit of fencing - I am open to ideas) to cover the gap between the metal post and the fence. See photos. I also need the hinge on the gate tightened. There is a small grub screw in the hinge that can maybe be manipulated so the pool gate closes from a resting position. Need this done before the 20th April.

Fence - 3000mm W X 800mm H Powder Coated Basalt Straight Top Matching gate to fit space of approximately 121 x 161

Welding my gate, it is lose with 4. Contact point.

**Gate Rebuild — Fit Composite Boards to Steel Frame (Willetton area)** Looking for a handy, detail-oriented person to help me fit composite decking boards to two steel gate frames. **The job:** Both gate halves have been stripped back to bare steel frames, treated and repainted black. I've purchased EKO composite screen planks that need to be fitted horizontally with a 4cm gap between each board. Boards will be fixed from the **back of the frame** using screws through pre-drilled holes in the square steel bar — so no fixings will be visible from the front. Gate will need to be rehung once completed. The key challenge is ensuring: - All boards run perfectly level and straight - Both gate halves line up exactly with each other **What I need from you:** - Experience with composite materials (pre-drilling, correct fixings) - Ability to work accurately - Comfort drilling through square steel bar - Own basic tools preferred (drill, bits, spirit level) **All materials are on-site and ready to go. ** Please include in your offer: - Your relevant experience - Whether you have your own tools - Your estimated time to complete Located in Willetton, Perth WA. Flexible on timing.

I am looking to get someone to assemble a Colorbond gate kit (from Teamwork Fencing) and install it in place of an existing wooden gate (removal of old gate will be done by me). I have purchased the kit and have it ready for assembly. Please note that the gate posts will not be concreted in to the ground and therefore, will require cutting to size.

Requiring new keys for our back gate. It’s currently unlocked but just for the sake of the dogs in the back would like to be able to lock it going forward. Landlord lost our keys so we just want them replaced

The old hinges have rusted and need to be replaced on gate that accesses under my house as well as a new slide lock

Old front gate is on a bit of a lean so gate won't close properly. Just need a repair to keep it going for now . Don't want a new gate at this stage . Needs a mcguyver!

Quick and Easy job. Need baby gate fixed to wall. You need to bring a Phillips head screwdriver. Won’t take more than 30 minutes. Need done today please

Hi, need the bracket for a new ring camera secured to my slatted aluminum front gate. Tried with a regular drill but I think it must need a specific drill bit to go through.

Want the gate securely fixed, structurally solid, and surrounding wall/render is repaired and restored to a neat, durable finish.

Need someone to pls fix wooden picket fence latch gate It’s a pool gate latch The wooden fence has warped from heat So latch is not matching up so won’t close properly Need just hinge moved over slightly

Centsys D5 EVO Electric gate needs restarting and setting. Has stopped working intermittently and at times won’t open or close (with remote). Currently on manual setting. Will need help with resetting the motor and getting it back up and running with the remote.

As per title, latch on front gate needs some New bolts. May have to be moved slightly to the right if the holes are too worn. It’s our rental property have flagged with prop Manager that it’s hopefully being done today.

I require 2 broken gate hinges to be supplied and replaced on the same gate.

3 metres width Colourbond gate needs to be replaced with something less expensive. The gates are damaged. This area is prone to high wind.