Find a professional gate installation in South Brisbane

1. Install 2 new Curtain rods 2. Reinstall 3 existing curtain rods (wall patching may be required) 3. Fix toilet spray holder to wall 4. Fix floor skirting (approx 6m) 5. Fix side frame if the fence gate

We need to replace the existing gate with the new aluminum gate please see photo 120w180h The new gate will be provided. Alternatively you can provide the gate and advise the additional cost for the gate and lock

Gate not opening. Error sign on box

I just need my side gate fenced. I have the wood ready to go

Need to Install a colorbond gate to the side of the house. One post is already at the place, and all the materials needed for the gate is already at the site, and dug a hole for the second post as well. There is 1.4m gap between the fence and the wall so need to install gate over there as you can see in the picture. Thanks

Under house fencing turned into a gate to allow access to under house.

1 wooden side gate has fallen off rusted hinges. Wooden Double side gate on other side now very hard to close perhaps due to earth movement.

Pool gate catches and does not close properly without force being applied.

We need a side gate and short fence section supplied and installed at our home. Gap between fence and house is approx 2.5m (and would like a gate that is hopefully approx 2.0m in width). Scope: • Supply a large prefab gate (eg Bunnings or similar) + hinges + latch + galvanised post + wood pailings + fixings. • Install gate with hinges on the right-hand side (may need gal post fixed against retaining wall or set in ground). • Add pailings to gate to bring height to approx 2.0m. • Fit latch. • Attach about 6.0m of 1.2m-high pailings to an existing fence. Open to suggestions too if there’s an easier or better way - we’re easy to work with, easy access to work area and parking. Looking to get it done before 23 Aug so we can secure side of house. Any questions please let me know. Cheers John

Our gates on the one side of the property are not properly aligned and do not close properly. Looking for someone who might be able to come and fix them if possible.

Hi, We need to replace the top lock on our gate to something more sturdy as the bottom lock sometimes fills up with dirt and the dogs are able to push out of the gate. We are thinking the same lock on the bottom gate but positioned sideways? Open to ideas. This gate is the only entrance into the house - the lock needs to be accessible to open from the outside which is why my thoughts is to do the same lock at the bottom but sideways

Need driveway gate rehanged and rusted hinges and latches replaced

We need someone to remove our current driveway sliding gate motor and install a new VEVOR 1800KG 4m motor kit: https://www.vevor.com.au/automatic-gate-opener-c_10530/vevor-sliding-gate-opener-automatic1800-kg-4-m-gear-track-750w-remote-control-p_010913436587 - Existing mHouse motor is functional but being upgraded - New motor’s mounting holes do not align - Dynabolting will be required (you’ll need to drill new mounts into concrete) - You’ll need to supply new mounting brackets or fabricate/adapt what’s needed - Power already available at the site - We’ll handle remote/app setup after install See attached image for the setup: - White aluminium sliding gate (approx. 4–5m width) - Clear, flat concrete base - Existing motor base is boxed and accessible You must have: - Experience installing sliding gate motors - Your own tools (hammer drill, dynabolts, angle grinder if needed) - Ability to measure and level the motor cog with the rack

Needing a timber gate put on the side of our house.

Drop the gate post into the ground and swing the gate.. level the ground and spread 3 m3 of wood chip. Gate supplied.. Can supply the wood chip and gate post..

I’m seeking an experienced handyman or fencing specialist to repair and enhance a side gate located between the front and back yards of my home in Eight Mile Plains, QLD. Requirements: • Safely remove the broken concrete and any associated debris. • Install a new, durable concrete footing suitable for a drop bolt anchor, ensuring stability over the gravel base. • Supply and install a dual-sided latch mechanism that allows the gate to be securely locked and unlocked from both sides. • Ensure the gate operates smoothly and is properly aligned

I’m reaching out to check your availability to help with fixing a few safety gates at my property. Some of them have become loose over time and may require re-securing—possibly using silicone, glue, or re-fastening with screws or brackets, depending on what’s most suitable.

We need to install a gate and small fence panel to create a dog safe area beside the house asap. Would need to be at least 1.5 high. The area is approximately 2 m wide. Thanks.

Bought new home. Building and Pest advised of high damp reading in bathroom. Need this investigated and rectified.

Need this gate replaced, dimensions 1.40m wide by 1.80m high. Thanks