Find a local glass fencing contractor in VIC

Hi all, I need a side lock relocated to the top of a glass door on a pool fence to be 1500mm above the ground

Glass pool gates need some adjusting for the magnetic latch to catch. One gate is not closing by itself. A total or three gates need to be inspected.

Cut 9 fence posts on a 60 degree angle for pool fence compliance Balaclava VIC 3183, Australia Cut 9 fence posts to 60 degree bevel angle for pool fence compliance. Should be a quick job. We are located in St Kilda East / Balaclava

Glass Pool fence needs two hinges replaced to be self closing to be compliant for pool. Please purchase your own hinges and replace current set. The hinge is 10 cm on the longest side and 5cm on the shortest side of the trapezium.

Pool fence hinge stopped working - spring tension is gone. Needs new hinge and realigning

We need someone to assist installing a supplied Bunnings glass panel section to a pool fence. Brackets, panel etc supplied. Just need labour.

Cut 9 fence posts to 60 degree bevel angle for pool fence compliance. Should be a quick job. We are located in St Kilda East / Balaclava

The pool fence in our backyard, including the gate has overtime lost its ability to close properly- and as such - we suspect it may not be compliant with the regulations. We want to address this and have the pool fence repaired to be compliant.

Gates - Nail timber slats back on Back Fence - prop fence until its repairs Balastrade - re-align glass Pool Fence, secure loose spigots Tiles - replace 4 loose pool tiles (above the waterline)

Spa fence gate has lost alignment preventing it from closing automatically due to impingement with adjacent glass fence. Gate secured on large post which may require re-alingment. There is a spacer between the posted and the deck balustrade which might provide potential for adjustment. Need someone with experience with glass fencing work.

Gates x 2 have sunken and need adjustment to swing shut to be compliant with state law

Glass pool fence installation with supplied materials (3 to 4 panels), plus compliance assessment for veranda sliding doors: could they be made to make compliance? Looking for an experienced and suitably qualified installer to put up a glass pool fence. We have all glass panels and hardware on site, including brackets, spigots and fixings. Installer to set out the fence line, drill and fix brackets, align and level panels, install gate hardware if applicable, and leave the job neat and safe. Second part of the task is to assess our enclosed veranda with existing sliding doors. We want to understand what would be required to make the sliding doors compliant as a pool barrier, so that in the future we could potentially remove the glass fencing and use the veranda doors as the compliant barrier instead. If you are able to do the compliance upgrade works as well, please include an estimate. Please include in your reply Your experience installing glass pool fences Whether you can provide compliance advice in Victoria and what you base it on Your availability An itemised quote for install only, and the additional compliance assessment and possible upgrade works

Need replacement pool gate measuring 920mm between glass panels 1200mm high 12mm thick 6 x holes drilled for hinges and latch And installed Need done before 2pm friday

Need to fix this pool gate to close better and latch to work.

Experienced Glass Pool Fence Installer Needed – St Andrews 3761 Looking for an experienced and qualified installer to install a glass pool fence in St Andrews (3761). Details: • 8 glass panels • 1 glass gate • Spigots supplied • Approx. 13 metres total • Straight run Must have experience with frameless glass pool fencing and ensure it meets Australian pool safety compliance standards.

I have a Highgrove frameless pool fence and need the glass resealed/re attached into the bracket on the ground and a replacement clip supplied by you if possible to join the corner together. Happy to FaceTime and show anyone what needs to be done but I’ve attached a couple of photos as well. At present the weight of the door which is attached to the next panel is forcing the Glass to fall towards the ground so resecuring the base will hopefully re-stabilise the pool fence. Thickness of glass appears to be different on each side of the corner.

Silicone that’s holding glass pool fence needs filling/replacing. One glass panel has dropped so will need to be lifted before re securing.

Our glass pool fence gate is struggling to close so we need it adjusted

I need a spa fence inspected for council

I have a pool gate which needs fixing . The paver the post sits on has moved and thus the gate now doesn’t close properly. Ultimately the post and paver needs removing , the paver re mortared down then post re fix and adjust to close property