Find experienced local fencing contractors in Central Coast

Measured already and existing materials available to build front fence 1.8- 2 metres tall about 20 metres in length- with a swing gate - colourbond and wooden slat or mod wood slats upper & may need to purchase wooden poles or steel dividers

Measure up for front fence 2 metres tall about 20 metres in length- colourbond and wooden slat or mod wood slats upper

Hi I need a front fence brick ( Approximate 5M ) with a 400mm base and 5 pillars supporting timber slats

Need someone to help with the fence repair

So we have an existing boundary timber fence that is part of our pool enclosure. It’s currently non compliant as it’s 1.5m high and it needs to be 1.8m high. The existing fence is timber. It’s around 7m is length. It’s currently 1.5m high, so the certifier said the quickest and cheapest way would be to add 3 palings across horizontally to give it the extra height (approx extra 30cm) So we need to add timber posts on existing fence and screw on the palings across the top. I’m happy to purchase the material. Just need someone to do the labour. Shouldn’t take longer than 2 hours

My fence was broken, I need someone to fix it. Thanks.

We have a colourbond gate at the side of our house. It is the width of a driveway and has two side that close in the middle.and attaches to the house on one side and the fence on the other. The half that attaches to the house has blown off the wall in the high wind and I need to repaired and put back in place as I have a dog that can get out

Need a new frame build for sliding gate, either in wood or metal. Whatever is cheaper. Just as picture shows. Size 180 tall x 210 wide

Looking to have this timber beam & the supporting posts replaced. Carport location. Would like merbau posts or something similar.

Looking to have this timber beam & the supporting posts replaced. Carport location. Would like merbau posts or something similar.

Front gate, repair gate paling and reattach hinge. Gate will need to be taken down, squared up and re-installed. Screws missing. Side gate needs to be rehinged, screws available

Erect several sections of Colorbond slat privacy screens and install a gate

Help to put the fence panel back. The frame at the bottom seems twisted and screw is loosing.

Remove front fence and gates (good condition, no longer needed). Fence consists of 6x aluminium panels and 2x brick pillars and is approx 14m long. Please provide quotes for removal only and removal+site clear and level

Side fence renew and fence gate lock

I have no idea how much I should pay for this so please pitch whatever. I have a short fence installed in my driveway that I need to bring forward. I have all of the required new pieces of fence and screws etc. I just need someone who has concrete drill and the time/knowledge to do it. The fence will need to be drilled into concrete with dino bolts. It is approx 3m across. There is a gate. It is metal stakes that go onto flat t feet (these will need to be drilled into the ground) I can help if you need but I have no idea what to do. I used PEAK no dig fencing, available at Bunnings. 1x PEAK No-Dig Mesh Fencing 860mm x 1200mm Black Steel Fence Gate 2x PEAK No-Dig Mesh Fencing 1500 x 1200mm Black Steel Panel 2x PEAK No-Dig Mesh Fencing 1200mm Black Steel Fence End Post with Spike (this will not be reused) 2x PEAK No-Dig Mesh Fencing 1200mm Black Steel Fence Post (I’ve bought 2 more of these to replace the spiked ones) 1 x PEAK No-Dig Mesh Fencing 600mm Black Steel Fence Standing Post Base (I’ve bought 3 more of these to replace the spikes) Plus 50mm x 10mm dyno bolts have been purchased to drill into the concrete.

TASK: Install a new letterbox on metal post, place in ground and remove the old one. SUBTASKS: (see accompanying photos 1. Assemble the metal post following instructions and mount the letterbox securely onto the post. 2. Remove the old letterbox and post from the ground. 3. Dig or enlarge the hole for the new post to ensure it fits properly. 4. Mix and pour concrete into the hole to create a solid base. 5. Install the letterbox/post in the concrete, making sure it is level and correctly positioned. 6. Secure the installation so the post remains stable and upright while the concrete sets. Concrete mix, shovel to dig hole,, and wheelbarrow to mix concrete provided.

Hi there – please see pics attached! I want to match my left-hand front fence to the right. This would involve: 1. Relocating the ‘sloped’ panel to the front. 2. Replacing the 4 x existing panels with higher ones. The dimensions of the panels I want to replace my current ones with, are approx.. 187cm high and 237cm wide. See pic attached/below!! *note: I have since had an arborist remove the overhanging branches in the pics, so there is clear access to install now. ****happy to discuss costs, $1k is just placeholder****

Dig a hole to install lattice in front of rainwater tank. Stakes to be put in ground to hold lattice in place. Three jasmine plants to be planted at the base of the lattice. Small border to be put around the jasmine plants and an echinacea plant that is already in the ground.

Urgent please I have all the parts I just need help putting together. This is an existing colourbond fence the top plates have been replaced. as the old ones were bent and panels had popped out. I have tried to do it on my own. my son was going to help me he has gone camping instead. I need to get it done so my dog doesn't escape.