37 Fencing Contractors in Adelaide

I am seeking a boundary fence supply and installed. 8 metres long colorbond both sides with concrete plinth. Currently no fence. Color to be advised.

Brush fence. Current height 1.8m would like to increase to 2.1m if not too difficult. 14m total of fencing. If height can be increased will need new gate installed too.

Approx 35mtrs of colourbond good neighbour with approx, 15mtr x 300mm section of retaining wall (fencing affixed to the retaining posts) and removal of old fencing.

Hi, I am looking for someone who can fix the rear fence. Some of the fence panels look bent. They need to be repaired. I am looking for a quote to fix this. I have attached the photos with this task.

Rebuild a very small section of a brick fence (2m (w) x 1m (h)) which has collapsed. The bricks are on site and have been cleaned and ready for re-laying. Will need someone to come with mortar and brick ties. The small job (we think would be about 1/2 day work) is in Kensington SA. Quote to include supply of mortar and brick ties please. We are looking for someone honest and reliable.

I require a handy man to install wooden slats onto a fence to create a deck like fence. Approximately 8 meters long and 1.8 meters high

I have a wooden/glass door that I need a doggie door put in to the bottom glass panel. I also need to extend a wire fence with one or two wooden posts to keep my dog in. I may also need a gate added.

We want to hire someone to install two side gates either side of our house. (Photo below of property- side gates are old images want to put similar gates on to replace)

I need the lattice work on my verandah sandblasted and resprayed. Lattice work has been removed already - need done in next couple of weeks

I need the edge of a carport/garage/fence straightened out. Unfortunately it was hit so the corner edge has been pushed in slightly, and I was envisaging that someone who knew what they were doing could remove the panel and beat it back into shape (and then reattach it:-). The crumpled edge is about 50cm long and I believe the colourbond (?) metal is attached to the frame with rivets. The metal cover is about 40 wide, 4cm deep, and ~2.5m tall.

I need help with fixing the fence panels, that have fallen off due to wind

Fence & gate (similar to black tubular pool fence) to be installed across driveway

I am building 2 blocks at 444 Portrush road, linden park. Need to fix the existing fence around the house.

I’d like to extend height of colorbond fence by 40-60cm. Prefer extension material to be durable eg plastic lookalike timber slats or trellis. purpose is to block out some light and add more privacy. Attached photos of fence. Size is 300cm length for main part and the perpendicular corner is 40cm. Attached images of current fence and what could work as extension (open to suggestions though) Flexible with day and time. Ready to hire asap even can be done this weekend if possible. Contractor to supply materials

Metal carport with 4 large poles holding up area of sheet metal paneling. 1/3 of the panel sheets has been removed. The 4 metal poles are screwed into the ground and the carport is approximately 4m tall

I need 8 temporary fence panels picked up from Stepney and delivered to rostrevor. 2.4m x 2.1m panel sizes.

Repair column damaged in car accident. Not structural. Painting not required. Materials will be reimbursed on provision of receipt.

I want wire rope strung between the posts of the iron fence to support my climbing plants. The posts are approx 2.4 m apart. There are 4 sections. The first two sections have two wires. I would like a third wire added high on the fence in those sections. The third and fourth sections have no wires. I would like three wires put in those sections. There are already holes drilled and I have 30m of wire rope, 2 wire rope grips and wire rope cutters. I have one tension hook. You will need 3 more tension hooks and two more wire rope grips. Wire goes across two sections through holes drilled in the middle post.

About 11.5m of front picket fence needs to be done. I have the timber slates, metal posts and rails. You need to supply the rest. Including AT fee, GST and any fees. The post will go in where the plinth is. You need to remove the plinth prior to installation of picket fence. We managed to lift some up already.

I have about 15m of chicken wire fence and star picketing surrounding small one bed house. This need removing before new tenants arrives this Wednesday. There is also little wooden gate that needs relocating back to where it was near front door. Post already there.