Find a local electronics repairer in NSW

A blue slip mechanic who is reliable and won't charge hundreds of dollars for what has too be fixed on Vehicle. I have had been ripped off in the past with all these issues they say need too be fixed that really don't. Not a rip off.Fair

The alloys need a touch up and some grinding. There a few stone chips and tow bar or golf ball strike to the front bumper, plus under scrape on one side. Open to suggestions too it’s a 10c ding and not on a sensor then rear it’s just a touch up on the bumper. I’ve seen a remote guy do my neighbours on site but I can drop her in. I’m also in Dee Why, Middle Harbour & Bondi often.

Apartment requires painting touch ups throughout - walls, doors, skirting, window trims, ceiling. Some examples attached. Would prefer completion in 1 day. Will inform paint colour - require this included in price. Floor plan attached

Require qualified electrician to install 2 LED ceiling lights

Change taps and spout in a bathroom vanity

LG inverter direct 14kg diamond glass smart drum with direct drive technology Stop mid cycle and show E1

The flush/water in one of my toilet keeps running long after flight. Can usually fix it temporarily but I need a permanent fix.

Need basin tap leak fixed leaking when we turn it off.

Job Title Wardrobe Dismantle & Plaster Patching (Upstairs) - DISPOSAL OPTIONAL Description Looking for a handy person or carpenter to completely dismantle a built-in wardrobe system from an upstairs bedroom and patch holes left in the drywall. Waste Disposal is OPTIONAL. Please provide a price breakdown in your offer: Base Price: Dismantle wardrobe, carry pieces downstairs, patch walls (leave materials stacked on-site). Add-on Price: Fully load and legally dispose of all materials offsite. The wardrobe is approx. 2.97m long. Scope of Work: Dismantle & Move On-Site: Carefully remove 3 floor-to-ceiling sliding mirror doors and their top/bottom tracks. Safely carry mirror panels down 1 flight of stairs; stack neatly on the ground floor. Strip out internal white melamine shelving, upright partition panels, and drawer runners. Note: Internal framing is nailed directly into walls/floor, not screwed. Please use a pry/crowbar to minimise drywall damage. Stack all timber neatly. Drywall Patching: Patch and flush-repair the rectangular drywall cutout/hole shown next to the skirting board in file. Patch any holes or surface tears left behind by framing nails. Optional Disposal: If selected, remove all timber, tracks, and mirror glass from the property. Requirements: Bring own tools (pry bars, track removal tools). Supply own plastering/drywall patching compounds. Must be physically capable of safely moving large mirror panels down stairs.

Remove 2 tree stumps (photos attached) One in the backyard, one in the front Location: Mt Pritchard

I need the walls to be pained in all the rooms except ceiling . Its a 2 year old house. Attaching the plan. Dont need painting on the bathrooms. Attached the paint as well used.

I left my scooter on all day and now the battery is flat. I need the scooter jump started.

Need these 2 driveway ramps drilled screwed into the ground. 4-6 screws each. So it stays put

4 stumps: approx 30cm, 35cm, 40cm, 40cm diameter 2 stumps in front yard, 2 in backyard Easy access via side gate to backyard Standard residential block Looking to grind to below ground level Flexible on timing over the next couple of weeks

Storz & Bickel VEAZY - Dry Herb Vaporizer Looking for an experienced electronics hobbyist or bench technician with micro-soldering capabilities (fine-tip iron, flux, and ideally a microscope setup) to repair a high-end dry herb vaporizer. The Device & Materials:Model: Storz & Bickel VEAZY (a premium, German-engineered medical-grade device). Casing Material: The outer shell and internal structure are made of medical-grade PEEK plastic (Polyether ether ketone). This is a highly heat-resistant engineering polymer, but it is tightly sealed. It needs to be pried open gently with proper plastic opening tools without snapping the plastic tabs or melting the housing during solder work. The Issue:The device has an internal connection failure. I need a technician to open the PEEK casing, inspect the main logic board, and re-solder the broken joint. This is likely: Option A (If not charging): A fractured pin connection where the USB-C charging port meets the PCB board. Option B (If not turning on): A loose/snapped power wire connecting the single-button system or internal battery to the motherboard terminal pads. Important Note on Warranty:Please note that I am deliberately choosing to bypass the official manufacturer warranty process due to the long turnaround times for international shipping as well as not purchased in Australia. Because opening this device permanently voids my warranty coverage, I need someone meticulous who will treat the board with care, apply proper flux, and ensure there are no bridges or short circuits before re-assembling. Logistics:I can drop the device off to you if you are located around the Campsie / Inner West / Canterbury-Bankstown region, or you can here. Please offer your price based on a quick bench diagnostics and point-to-point micro-solder reflow.

We need to replace 2x bathroom basin taps that are constantly dripping / not shutting off. We have purchased replacements, just need someone to remove old and install new

Looking for handyman to put new table tops on these existing pole stands. 6 tables.

Assemble a desk and a wardrobe

Need to hang 3 pendant lights with shade, I have the lights and cords and shades. Change from Led downlights.

Need stumps of banana trees and some small shrubs removed