Find a local electronics repairer in Gold Coast

Halo brand GHD hair straightener turns on but turns off again after a few seconds.

Need a plumber to put in my new taps. And 2 shower heads. They are silver so I want the new black ones in

5 of these trees to be cut down and the stumps removed ( stones around stumps to be moved aside when job is being done)

Touch up of external painting on our home

Shower head keeps on leaking Address: 5 Clifford St Surfers Paradise , Gold Coast, QLD, AU, 4217

Need help building a timber frame for steps through this garden. probably 3 hours work

Looking for someone to put a Darche Eclipse 180 G2 awning on my Toyota Hiace and then give me a little demo on how to use it. There are already roof racks on the van, I can send you photos and measurements beforehand and you let me know if there are additional bolts etc you need so I can organise it before the job. Looking for people who have worked with this awning before. Thank you.

I have a Bose NC700 and I can no longer charger

I have 2.5 meters top soil I would like to move in a wheelbarrow and spread out flat area not far to move it

I need two outdoor concrete staircase built. The bottom staircase is about 9m x 2.4 m and the top is about 5m x 2.4m. I'm happy to chip in on the labour

I have a small dent in one wall, and on another two walls the paint has chipped off

I have FTTP NBN with the NBN fibre box (NTD) located in the garage. Currently, my router connects via ethernet to a data point downstairs (study). I want to keep this existing downstairs connection and add a second Cat6 ethernet point upstairs so I can relocate the router out of a new nursery. Scope of work: • Run one additional Cat6 ethernet cable from the NBN box in the garage to an upstairs room • Install one ethernet wall plate upstairs • Keep the existing downstairs data point active • Terminate and test the new connection House is two storey. No NBN or ISP work required. Licensed cabler required.

Hey! Need two holes patched up in the bathroom. And potentially need filling of a 50c sized dent downstairs. With the bathroom holes, one is an inspection hole directly above the shower head and the other is broken gyprock hole from a broken off towel rack. I will paint. Ideally need it done before the 23rd.

Posting for my parents place. Want to completely replace the entire bench tops with a simple ikea worktop. Might consider getting a new sink as well depending on budget.

I need two bedroom walls prepped and painted (two coats). Substantial sections of existing paint peeled off after removing peel and stick wall paper. Will need appropriate prep (sanding etc) to ensure the surface is smooth and you can’t see surface transitions. In addition there are around 5-10 small touch ups required on other walls (approx size 50c piece) where a small patch of paint has peeled off with 3M renters tape removal (fill, sand and paint). I’ve obtained colour matched paint (4L). Tasker to provide other necessary tools/ floor coverage to ensure no paint goes on carpets and fully clean up after job. Job must be finished before 12pm on Monday 1 Dec. Thanks in advance

3 trees need tops trimmed off them. They are tall and thin so wouldn’t need a chainsaw. The stand alone ladder would need to reach 5m high as we don’t want the tree leant over and roots damaged. Type of gardening: Other Size of garden: Under 50m² Has green waste bin: Yes

I need two large stumps removed. Pics attached.

Renovating laundry. Need washing machine taps lowered to roughly 700mm off the ground. Will be a bench top going in so the aim is to keep the taps and hoses hidden. Pipes are copper.

We need to remove existing basin tap set and install a new 3-piece set. Work required: • Remove old hot/cold taps and spout • Install new set • Replace the old copper tails with flexi hoses (I have already purchased the flexi hoses) • Connect everything, seal properly, and check for leaks • Access is standard under-sink vanity

I just need someone fo chainsaw 2 x large tree stumps to ground level But we will clean up mess just cut up so we can lift to the Ute tray