Find trusted local electricians in Rochedale South

scope of work 1. Disconnect existing freestanding cooktop connected to 32A breaker 2. Install a new ceramic cooktop (6.6kW)) to the exisiting 32A / 6mm2 circuit. Cooktop isolation switch already exisint 3. Install a new 10A plugin oven (max power 2.1kW) to the same 32A cooktop circuit. Jbox already behind the wall. Or, 4. Tie into the 10A GPO nearby but will need to be re-routed Cabinetry and benchtop will be cut to size - no cabinetry work required. My understanding as per the wiring rule both cooktop and oven can run on a same 32A circuit but pls confirm. If a new dedicated circuit is needed for the oven, switchboard is about 3m away from the kitchen - lowset house with roof access. Pic of switchboard attached Location Rochedale South

Remove and change light fitting

Need about 12-14 downlights to be installed around the house and in the alfresco area.

Hello, Are any electricians available. Happy to pay cash or card. I have a Hisense Split System air-con, back to back installation onto a bedroom wall. Thank you.

Supply and install 2 double and 1 single power points. Double powerpoint behind tv. Powerpoint is too close to bed. Require double located further from bed. Single powerpoint at photo 3. Price negotiable.

Findings: Something is causing the HWS to trip twice so far and now no power supply at all. Possible faulty circuit breaker or isolation switch. Circuit breaker's maximum capacity 16A while the breaker should technically handle the load, sustained operation at Or near the maximum rating can cause overheating or nuisance tripping.

I have four bedroom house and ducted in whole house . So it need to be clean

New double power point 3 x power switches that wont push on one been the stove

A ceiling lighting base with a circular fluorescent bulb was functioning well with bright light. The bulb is fairly new. Couple of days when had the light turned on, it suddenly went off with no previous warning or indication that it had an issue. When I replaced the used circular fluorescent bulb with a new bulb and as soon as I turned the light on, only one flicker of light appeared for a second and the light did not work at all. I do not think the problem is in the bulb. It could possibly be in in the electronic ballast. If the electronic ballast is to be replaced, my preference is that the base fitting would be still suitable to refit the existing flat glass cover and its oyster glass cover over it. Attached are photos of the lighting base with the bulb taken off and another showing the circular fluorescent bulb type. The external diameter of the metal base is approximately 320 mm which is almost the same size as the opening of the flat glass cover with the opening showing in the attached photo. The depth of the metal base is approximately 30 mm. The fluorescent bulb size is 16 mm and its external diameter is 245 mm as showing in the attached photo of the box. The diameter of the oyster glass cover is 340 mm.

My hot water system has stopped (Heat Pump 15 years old). I am changing to a continuous gas supply and need the wiring that I have disconnected safely to the Heat Pump, attached to an outdoor wall plug that I have purchased.

I dropped the lamp and it looks like the wiring has come loose.

Electrician to disconnect and make safe a number of flourescent lights, 3x ceiling fans and 2x spot lights. Will also discuss on person further work to prewire 6-10x GPO's, 12-14x LED spot lights, two pendant lights and 2-3 outdoor lights for signage uplighting. This task is solely to make disconnect and make safe current lights and fans.

Looking to have 2 power points installed - 1 is where an old stove used to be wired in. Need done Monday before plumber installs new laundry. - 1 is a new point in a kitchen (not sure if it’s doable - not urgent)

- Disconnect old electric stove - Check 1 sparking power point - Move 1 tv point

Need price to Replace cooktop on bench labour only - Due date: Flexible

Hello, I’m currently in the process of finishing off my transportable home that I’ve turned into a grannyflat and we’re finishing off the bathroom at the moment. I’m looking for an electrician who is able to put in a PowerPoint in the bathroom and also change a light in my bedroom to a fandelier. I also would love an LED mirror in my bathroom as well but unsure if that’ll be too painful to do so would like to discuss that. Thank you so much for your time. - Due date: Flexible

House wiring inspection and repairs if needed, 2 outside lights removed and a power point replaced. - Due date: Flexible

Looking for a licensed electrician to upgrade a main switchboard. Current switchboard photo is in the attachment - Due date: Flexible

I need an electrcian to install a power point and Conceal TV wires behind the wall so that they don't show. Due date: Needs to be done on Thursday, 2 November 2023

Looking for electrician to come out and give me advice for the best way to run all of our power boards and plugs for our Christmas display - Due date: Needs to be done on Tuesday, 31 October 2023