Find a cladding professional in VIC

Hi 👋 I’m looking for an experienced carpenter / cladder / skilled handyman to finish the external cladding on a tiny house. Job details: • Finish remaining external wall cladding • Approx small area (around 10–20m²) • Cutting and fitting around windows/edges already done • Ensure cladding is straight, secure, and weather-tight • Neat finish is important Materials: ✅ All materials are already supplied (cladding boards, trims, fixingsetc.) You just need to bring your own tools & big ladder for roof access Location: Montrose, VIC Access: Easy access Timing: Flexible – can be completed over 1–2 days depending on experience Looking for someone who: • Has experience with cladding or external carpentry • Can work independently and problem-solve • Takes pride in a clean, tidy finish Please include in your offer: • Your relevant experience • Estimated time to complete • Whether you charge hourly or day rate Happy to answer any questions and share photos of the remaining areas to be completed. Thanks! 🙂

Looking for an experienced carpenter/chippy to clad nib wall and the underside of an existing mezzanine floor ceiling with 12mm plywood. Scope of works: Fix 12mm ply sheets to underside of mezzanine Install some back blocking and noggins as required Neat finish around existing services/edges General tidy workmanship expected Materials supplied: 12mm plywood Timber Screws Liquid nails You will need your own tools and experience doing similar work.
Access is clear and job is ready to go. Please include experience/photos if possible.

Hi Looking for an expert installer in James Hardie matrix cladding We have an external wall on a second storey where the cladding seems to be allowing water inside. Looking for an experienced installer to replace all the bottom pieces and upgrade the flashing underneath to ensure no rain water can get in. Job is on second storey. Has easy access but will need some scaffolding. Will need the panels to be pre painted before being installed also to make it easier on painting. Straight forward job for someone who has the right experience. There are about a dozen pieces needed for replacement (not all are pictured). Just the bottom pieces only. Thanks.

We built a 5 × 7 detached granny flat, and need to install external cement sheet cladding and eaves. It's a 6mm fibre cement sheets. I have already purchased all the materials. You just need to have a coil nail gun. I believe it’s a one-day job.

Put wall cladding in 5 wall. May be need adjust cladding on side of wall. I have glue

Need someone to install L Corner for ceiling cladding..L Corners are supplied

Looking for an experienced handyman who can supply and install decorative cladding on the exterior of my shed to make it look more modern and visually appealing. The structure is already built (see photos). I want to upgrade the look by installing nice exterior cladding on the visible side. Location Ringwood

Cladding installation required in 3 walls in the house . Ceiling height is 2.56 metres and room 1 width 3.6 metres and room 2 width is 3.5 metres and room 3 width 3.40 metres

I looking to get the timber cladding done in TV space wall and a couple of other places too.

Looking for someone to supply and install WPC paneling for my roof eaves. Will need some Timbers as well before WPC goes on. Supply and install approx 75 linear meters - of the 75 linear meters approx 12m is a metal roof sheet the rest is all standard tile Single level home (one section is approx 4-5m high)

cladding needs to be installed on INNER and OUTER Alfresco top corner where wood is installed. I have purchsed the cladding but don't have nails, tools and parts required to finish the job I'm flexible with date and time. Should look seamless (wrap around the wood installed) and not a patchy job. Based in clyde evergreen. Thanks

Hi, looking for a carpenter to repair the weatherboard and sarking on roof per photo. Thanks

Assembly of a bar bench 100 W x 90 H x 30 D (cm) following instructions sheet and cladding with slate panels to be cut to size on top and the two sides

Seeking technical implementation advice on method material and technique of internal cladding installation into brick wall. I intent to use the concave panel cladding as pictured to make feature walls in my house. I would like a reputable tradesman’s opinion with explanation on how to install it properly. Depending on my decision, I may offer the task to the contractor or complete myself but this task is specifically for a technical explanation and provided solution on best practice installation.

Two sheets of thin wall cladding have become unattached and need re-fixing to the house structure under the point of the pitched roof.

Want to paint timber cladding to Charcoal color. Paint will be supplied

I need cladding on approx 8m of my back fence and 5m of side fence behind my pool so it’s not climbable. I want monument colour please. Is there anyone out there that can do it before Christmas? Thank you!

I need all the tiling taken off a wall as they are falling off and then colourbond cladding installed. Approx 4x2.5m Price to include - removal of all tiles - disposal of tiles - install of colourbond cladding installed Cladding material will be provided.

I need 20 weatherboards @ 4.2m replaced. Plwase quote for removal and replace

Two of the claddings installed in the outdoor area are a bit short (see attached photos) and they need to be replaced with new ones. To replace the two, the carpenter needs to undo a total of 5 claddings. The over all job should not take more than an hour and half. Please let me know if anyone is interested in doing the job. Location: Caroline springs.