Find experienced local carpenters in Wurtulla

I need 2 white concrete basin tops made. 1@1200x600 (1 sink positioned right side) 1@1500x600 (1 sinks ) Both at 200mm high. See attached photo for design + approx dimensions. Job is at Wurtulla

Replace 7 x 6.0m polycarbonate sheets on a patio. Screwing into timber. All materials supplied. Quote is for labour. Thanks 👍

Need a couple of tradesman to put up shed. New shed from cheapsheds comes with instructions and takes two people. - Due date: Flexible

Need some timber frame walls built for an internal renovation of a house would suit a carpenter for a day - Due date: Before Tuesday, 28 November 2023

We need a gable roof garden shed built - link to shed here https://easyshed.com.au/products/gable-roof-garden-shed-3m-w-x-1-5m-d-classic?utm_campaign=order-confirmation-email&utm_medium=email&utm_source=OrderlyEmails&utm_content=product - Due date: Before Monday, 6 November 2023

Needing an Absco shed assembled - 3.00m width x 2.26m depth x 2.00m peak height. Concrete slab already poured. - Due date: Flexible

Garden shed has some minor panel damage that is needing to be repaired. I have all the new shed sheets that need repairing

I have a large timber deck and the nails holding the slats down are popping up by about 3-4 mm. If possible I would like someone to replace the wrong nails with screws to rectify this. The deck area is about 60m2. Happy for someone to measure properly to quote accurately. - Due date: Flexible

3w x 2.26d x 2h absco shed purchased from bunnings. Need the concrete slab poured and shed assembled. - Due date: Before Friday, 10 March 2023

We need someone that can erect a small garden shed and bolt it to a concrete slab. Shed is 2.1 x 2.1m we have all the parts to erect it and secure it to the slab. Ideally you would have your own tools but we do own a few drills that would probably get the job done. Ideally ASAP. - Due date: Flexible

We need a custom built shed to fit between our neighbour’s fence and our existing car port. - timber frame - clad in Colourbond (Monument Grey) - current concrete slab isn’t level - needs levelling concrete or be able to build to slab fall away - must be weather proof (good seal between walls and floor) - we need 2 roller doors that fit between existing carport posts (see diagram) Dimensions: - 2100mm deep - 5700mm long - 2100mm high - 2 roller doors 1200mm wide - roller door 1: 1305mm off road end - roller door 2: 2805mm off road end Must source all materials (I will cover the cost of materials). We need someone with experience, someone trustworthy and someone that is confident they can successfully complete this job. Please reply with evidence of experience. Happy for you to come round and check out the space before committing to the build. Location: Wurtulla

need someone to build stud walls and install gyprock. I will assist them - Due date: Needs to be done on Monday, 7th Feb 2022

Looking for carpenter or handy man to hang 16 internal doors. Replacing current doors in house. 7 are room entry doors 9 are wardrobe / cupboard Sizes vary from 420 - 820 and have been ordered to size Just need the hardware added and hung

I have a Skillion roof garden shed to install at my place. Measurements are: 1.5m (w) x 2.25m (d) x 2.1m (h) It also has concrete fixings to be fitted to the slab and a louvre window to be installed.

Need quotes for skirting boards to be replaced. I’ll have new skirting boards ready.

Have a finished laundry blackbutt timber countertop. I need the length only cut to fit, as well as a laundry above mount sink hole cut to fit a sink we already have. Also need 2 approx 40mm holes cut for bathroom vanity cabinet sink and tapware. Also blackbutt timber. Need done asap.

Need a cabinet maker to cut out laundry sink hole (above mount) and fit laundry benchtop. Benchtop is cut and finished just needs a final cut to length to fit. Need 2 hole cuts for bathroom vanity for countertop sink and tapware. All blackbutt timber. Job is in Wurtulla.

Build & install two small wooden shelves in this little corner. Would prefer wood not laminate. Wall dimensions are 60cm x 40cm. Corner rounded off as will be in line for good head hits haha See photos of space.

Remove old shed from site. Assemble new 3x3 shed (from Bunnings). Dump waste. Date and time negotiable

I am replacing my existing laminate bench top. I already have the new laminate bench top, I need help to install and cut out the holes for the sink and the cooktop. I would prefer someone with experience and has done this before.