Find a professional staining service in Melbourne

Clean, sand and stain (2 coats) an outdoor deck, outdoor table and two bench seats please.

Deck needs to be sanded back and then re-stained. 3.8m x 4.5m

We are moving out of our house and need the back decking (6m x 6m) cleaned, sanded, restrained ready to rent out. We are moving on the 11th Nov and need completed by 13th.

Underbench shelving to be cut down to fit an fridge.

I have recently left my apartment and to receve my bond back i need to repair my door frame from chips from a mirror that hung over the door. My car has also left some coolant stains on the parking spot ground and needs cleaning.

Looking for an experienced marble or natural stone restoration specialist to remove marks from a kitchen benchtop. During recent plastering works, a plasterboard sheet was left on the marble kitchen benchtop, resulting in visible white/cloudy marks on the surface. Scope of Work: * Inspect the affected marble surface. * Determine whether the marks are plaster residue, staining, or surface etching. * Professionally clean, polish, or restore the affected area as required. * Restore the original appearance and finish of the marble as closely as possible. * Ensure no further damage occurs during treatment. Photos attached for reference. Please only respond if you have experience with marble benchtop restoration and the appropriate equipment. Location: Melbourne CBD / Docklands Please provide your quote and availability.

I have a restaurant and need a 9cm hole placed in a stainless steel benchtop. The bench has a stainless steel top layer with a wood layer underneath. Hole needs to go through both

Stainless-steel cables for landscaping trellis that have been hydraulically crimped/swaged at the ends. I need the cables shortened and then securely refastened to an existing concrete wall.

Title: Extend Existing Stainless Steel Café Bench – Melbourne CBD Hi, I’m looking for an experienced stainless-steel fabricator or welder to modify and extend an existing stainless-steel bench at a commercial café in Melbourne CBD. The existing bench section measures approximately 500 mm, and I need to extend it to approximately 700–800 mm, with the final measurement confirmed on-site. The bench will support a commercial 2-group coffee machine weighing approximately 90 kg. Scope of work: * Supply and install a suitable stainless-steel bench extension. * Reinforce or support the extension where required. * Ensure a strong, stable and level working surface. * Provide a neat, smooth finish suitable for a commercial café. * Complete the necessary fabrication and installation on-site. Photos of the existing bench are available. Looking for someone experienced in commercial stainless-steel fabrication who can complete the work professionally. Location: Melbourne CBD, VIC 3000. Preferred date: Friday, 23 October 2026, or flexible by arrangement. Please submit your offer for completing the work, including labour and materials, through Airtasker. Thank you.

To restore floor in Kitchen with minimal disruption and repair squeaks in the floor. Patch One: 1740 mm x 390mm Patch Two: 640 mm x 390 mm ( by microwave)

Strip away the old, peeling silicone along the stainless steel benchtop-to-wall join, thoroughly clean and degrease the contact surface, and lay a smooth, continuous bead of mold-resistant neutral-cure kitchen silicone across the two gap sections.

We are looking for a professional floor sander who can sand (to level) our outdoor back deck. The deck is 5m x 5m in size. Must have own equipment.

Need about 4 holes filled through this stainless steel bar to allow for cables to run below. Each hole to be about 6cm in diameter.

Looking for someone experienced with wall mounting to securely install 2 stainless steel shelves above my coffee station. I’ll attach a photo of the actual unit/coffee machine and a render showing roughly how I want the shelves positioned. The shelves need to be: * centred properly on the wall * level and securely mounted * with the lower shelf around 2–4 inches above the top of the coffee machine * evenly spaced above each other Please note the shelves look slightly off-centre in the render, but I want them properly centred to the wall in real life. Would prefer someone with experience mounting shelves and checking wall type/fixings to make sure they’re secure.

Looking for someone to install a stainless steel wall shelf onto the brick wall pictured. Shelf, brackets and original mounting hardware/fixings are all supplied. I also have the installation instructions. It needs to be mounted securely and level on the front of the brick wall, underneath the TV, just below the power points. Please take appropriate care when drilling and ideally have a detector to check the area before drilling. Should be a fairly quick and straightforward job for someone with the correct masonry drill/tools and experience mounting into brick. Located in Prahran. Happy for you to use your own suitable masonry fixings instead of the supplied ones if you think they’ll provide a better/safer installation.

Two floorboards are damaged and need replaced. The replacement boards don't need to perfectly match (this is coming ahead of a later renovation), but a close stain would be great.

I need a clean circular hole cut into the side of this steel cupboard. I cut a rough hole in it myself to feed the washine machine hose through, but I need a cleaner hole cut in before I move out. The laundry cupboard has one of those slim stainless-steel laundry troughs with a storage cabinet underneath, next to the washing machine. The washing machine will be moved out of the apartment on Friday 7 Aug so I'd like someone to come on Saturday 8 Aug.

Bathroom wall has stains on it. We need to repaint the whole wall or fix the stains. Refer the pictures.

Needing a good floorer to sand and stain floors in rooms as photographed. Hope you can start on Saturday. We want to bring the floors back to natural colour of timber and stain would be clear coat matt finish. Please note this includes the steps on the stairs as well