Find a professional staining service in Melbourne

As per photographs, our deck could do with a refresh, preferably two coats. It will require a few visits to allow for moving things to one side to stain and dry before moving things back onto freshly stained area. It’s about 5m x 5m and has three steps. 1. Pressure wash 2. Replace some lifting nails with special screws we’ll provide 3. There’s no need to move the large rectangular planter boxes, just reach under to stain, but will need to move smaller pots, table and kennel to one side of deck at a time to stain - we can help 4. Stain one side at a time using mop applicator AND a brush, the gaps between the boards are large enough that the inside edges need to be stained using a brush 5. Care is necessary to avoid drips, because our deck is over a common entrance where neighbours drive their cars in and out so we don’t want drips falling on their cars - we will warn them of timing 6. We have the stain and can buy more as required

Paint has peeled off the wall exposing the plaster. So it would need some filler then sanding and paint. Also the window cill and a bit of the skirting board needs painting. Acrylic paint on the carpet. So it needs a good steam clean. Finally a new desk top need to be screwed to the legs.

Looking for someone who has a good drill to put stainless steel shelf in the commercial kitchen.

Looking for someone to come and prepare, sand and stain a deck using sikkens products. Probably 3 coats for lasting protection!approximately 6m x 4m area including fence and built in bench seat

I need someone to get rid of the monstera roots that are stuck to the wall and plaster over it

Looking for someone experienced to install a stainless steel shelf onto a custom-built wall. • Wall is timber frame with Alucobond panel on top • Shelf needs to be securely drilled and mounted • Must have own tools and experience working with this type of surface Two people will be onsite and will hold the shelf up

Sand back and restain existing back decking. Deck Size is 8.4 x 3.4m. See photos which show area as well as existing damage to some boards so you can see what needs to be done.

Cost to repair the broken / pushed out section in a front entrance door. Keeping the existing design. Dimntionw of the entire panel pictured is approx 1000mm x 600mm. Please have done similar repairs before

Hi - need someone experienced to clean, lightly sand, stain and seal the following: A. Front porch deck (approx 7m sq). B. Outdoor pergola. C. Small outdoor barrel sauna. I can provide 6 litres of decking oil (natural)but need you to bring all tools and rest of supplies needed. Thanks

We need someone to cut the legs 40mm shorter on a stainless steel bench top so that it aligns with an older unit next to it. The legs are hollow square profile thin stainless steel

I’ve got a merbeu deck which is 1205 x 3200 plus 2700 x 1350 which needs to be sanded and stained. I can supply the oil, but all other equipment will need to be by you.

I need my decking prepped and restained. Its 13x2m. It’s in fairly good condition as far as screws etc goes. Just sun damage to the surface. I’m open to advice on what stain to use and can purchase that separately. Ground floor. Easy access and parking.

Need to fill this holes and fix/paint or try to minimise these stains

30metre2. Looking for someone to clean and stain my outdoor deck including side panel decking and 2 x small stairs. I do not have any of the stain / tools required

I have the decking paint, I just need someone to prepare and paint/stain the wooden panels on my balcony. There are two ends that need painting that are approximately 3m x 3m and a harder to reach area above the windows and doors to my balcony which is approximately 6m in length and a bit under a meter in height. I have the paint.

An existing deck approx. 6m x 5m to be oiled for maintenance purposes along with a cupboard that contains a hot water unit.

I am looking for someone to stain my decking with a triple coat on two floors (see photos). I will supply the oil stain (Intergrain UltraDeck Timber Oil). No sanding required.

We’re looking for a skilled painter to paint or stain this timber feature wall black in our new office space in Cremorne. The wall is approximately 11 sqm. Details: • Timber panel wall currently finished in a dark brown stain (see photo) • We’re after a smooth, even matte black finish — open to either paint or stain based on your recommendation • Includes prep work (light sanding or cleaning as needed) • Please supply all materials, tools, and protective coverings • Care to be taken to protect the surrounding walls, ceiling, and carpet • Ideally completed within the next week Location: Cremorne, VIC Area: ~11sqm

I have an outdoor table with a wood top and wood arms on the chair - I want it sanded back and restrained in a dark walnut stain

Coffee pot exploded and coffee grounds stained on walls and ceiling. Tried to scrub but it’s still there, if you have a wall steamer or can recommend how to clean would be eternally grateful as renting! Happy for offers