Find experienced local carpenters in ACT

3 western red cedar doors need runners replaced and maybe new cover tracks

I need a Shopfitter/Cabinet maker or carpenter with interior experience to help chop out the last few days of a fitout. 2-3 days work

Build a cabinet above fridge using the shelves from the exisiting cabinets so it matches when looking from the front and runs across to wall above the fridge.

There are some rotten planks in our deck that need replacing- the sections need sawing off. Planks are 147mm x 31mm. Original ones were custom made but replacements don’t necessarily need to match.

We have a wooden sash window (approx 20 years old) that won’t close properly, I’ve also noticed that the plastic on the top right-hand side of that part of the window appears to be dislodged. The other window in that room has a similar issue. When we open that, the window won’t stay straight in the frame. Could you please provide a quote?

Remove old two steps & two stringers; Install new two steps & new two stringers supplied from bunnings. Note the bunnings pic is three steps but the material I have already purchased is only two steps, & two stringers. No painting necessary.

Photos attached below, I am wanting to tidy up the trim beside an induction cooktop we have recently installed, and also create a drawer below the new oven. Black finish in both instances.

Cabinet with two tiers with four drawers on each tier External dimensions not to exceed 2400 (wide) x 450 (deep) x 450 (height) mm cabinet to be made from laminex spotted gum veneer Drawers to have bevel edges with soft close No legs required

Need to cut four sliding doors by 20mm - melamine body and steel frame.

Custom Wall-Mounted Laundry Shelf Unit – Supply and Install Looking for a carpenter or handyman to build and install a wall-mounted laundry storage box made from moisture-resistant (MR) white melamine. Specifications: - Material: 16 mm MR white melamine with matching edging - Outside dimensions: 565 mm W × 750 mm H × 400 mm D - Structure: Open box with two adjustable shelves - Pin holes drilled for shelf height adjustment - Finish: Pre-finished melamine, no painting required - Mounting: Secure wall-mounted installation included Requirements: - Box to be built off-site and delivered for installation - Installer to supply all materials, tools, and fixings - Must ensure sturdy wall mounting suitable for laundry use Access: - Two-bedroom apartment with basement parking and lift access

Where the current white Ikea cupboards are - we want to replace them with 2 floor to ceiling cupboards. The cupboard closest to couch / plants will have a desk inside. Then in front of kitchen we want a bench seat built with storage under. Same colour & material as the kitchen cupboards next to the fridge. Current space - measurements approximately 2m where the white cupboards are x 2.250 where the bench seat will be built. Pictures attached of the current space & ideas. Note: No budget set as I am not sure how much this work will cost. Looking for quotes.

Need to build a cabinet in a corner part of lounge room for display and storage shelves

Two pieces of wood I’ll provide. Need to cut two arches at the top. Can use jigsaw or router . Own tools

We have a beautiful 6 seater dining table, solid dark wood, but it’s just a bit too high for our family. We’d like someone to come and shorten the legs for us by about 10cm. It is a small job but a lovely old table with sentimental value so would like this to be done to a good standard and ensure no wobble/uneven legs.

One of the legs of our dining table recently broke. We need a handy carpenter to either rebuild the leg, or fix the current one. Click on below dropbox link to see PDF containing images and details of the break. https://www.dropbox.com/scl/fi/yedzvkixliwfwil7o04j8/Our-dining-table.pdf?rlkey=dg6pqiic0g2pkayyxz56j8k1t&dl=0

Recently install gas cook top & gas plumber unable to fixed the kitchen drawer as power shocked back side wall is between , so need to adjust drawer to make it fit

Require the gap between IKEA walk in robes and the wall to be filled. Details: - Suitable infill panel cut to size and fitted - Skirting panels to be continued across infill panel. No painting required, I will do this after fitting. Thanks

Hi there, Looking for an experienced handyman or carpenter to help with some front and back porch upgrades: 🔨 Tasks include: Installing timber tops on approx. 15m of steel railings (front and back porch). Adding wood cladding or rendering to a pillar approx. 4–5m tall at the front porch. Painting timber tops and ensuring a neat, finished look. 💡 Materials: The price I have included is for labour only, as I am hoping to supply materials myself, however I may need some guidance on what to get. If you are happy to supply materials instead, please include that in your quote. 🖼️ Note: I have attached images of my railings and pillar, along with a couple of inspo pics for what I’m aiming for. Thanks!

I have a hallway table that is about 3mm too wide for the VERY snug entry way space. Looking for someone with a wood plane - to shave off the 3-4mm needed to make the table fit. Total surface area needing removal is: Two sides, each 21.5cm H x 40cm W If you have sanding/polishing equipment - that would be helpful also. Would need to do work in situ (at my place) so we can test when it is enough to fit.

I need an approx 3-5cm hole drilled in the side of a cabinet for a cable, then a cable grommet fitted (which I will supply)