Find experienced local carpenters in Adelaide

I need a wrap around desk built into my office (pics included). Found the timber I want from bunnings, don’t need anything fancy as the table tops are as I want them. Just need them cut to size and sturdy legs built that are attached to my wall and flooring. I’ve also included an AI mock up of how I’d like it to look. The Timber I want to use from Bunnings is SpecRite 2400 x 900 x 33mm Brown Acacia Multi-Use Timber Panel

WANTED – Custom Van Floor & Raised Platform – Adelaide Looking for a carpenter, cabinetmaker or van fit-out specialist to supply and fit a timber/MDF floor and raised platform in my 2015 Renault Kangoo, similar to the attached photo. What I need: Flat MDF flooring throughout the cargo area. Raised platform towards the rear doors, approximately 200 mm high and 800 mm deep. Flat MDF top with sturdy timber supports. Open storage underneath, with MDF on the bottom floor. Front section behind the seats kept flat and clear. Neatly cut around the wheel arches and securely fitted. The van will carry batteries and a toolbox, so the setup needs to be strong and suitable for the load. Final measurements to be checked on the vehicle. Located in Kent Town, Adelaide. Please message me with your availability and a quote including materials and installation. Photos of similar work would be appreciated.

WANTED – Custom Van Floor & Raised Platform – Adelaide Looking for a carpenter, cabinetmaker or van fit-out specialist to supply and fit a timber/MDF floor and raised platform in my 2015 Renault Kangoo, similar to the attached photo. What I need: Flat MDF flooring throughout the cargo area. Raised platform towards the rear doors, approximately 200 mm high and 800 mm deep. Flat MDF top with sturdy timber supports. Open storage underneath, with MDF on the bottom floor. Front section behind the seats kept flat and clear. Neatly cut around the wheel arches and securely fitted. The van will carry batteries and a toolbox, so the setup needs to be strong and suitable for the load. Final measurements to be checked on the vehicle. Located in Kent Town, Adelaide. Please message me with your availability and a quote including materials and installation. Photos of similar work would be appreciated.

Inside timber broken (looks like water damage)

This book case was primed and painted (4 coats) but I’ve accidentally gone half strength rather than full. I need someone to paint full strength (paint supplies) - 2 or 3 coats. No shelving requires.

We bought a PAX cupboard from IKEA but it is too tall, I need 6cm to be sawed off the bottom of 3 wooden planks. You can either bring your equipment and saw it off at my place (in the garden), or bring it to yours to saw, and bring it back.

Looking for an experienced kitchen cabinet installer or skilled cabinetmaking handyman to assist with kitchen installation in a new residential home in Glen Osmond. All cabinet carcasses are pre-assembled and all materials are on-site. Installation has not yet commenced. Scope of work: * Read and interpret kitchen cabinetry plans. * Position, level, align and secure base and wall cabinets. * Install drawers, doors, kickboards, fillers and finishing panels. * Cut, trim and modify panels where required. * Complete installations to a professional standard. Requirements: * Must have previous kitchen cabinet installation experience. * Able to read plans and work independently with minimal supervision. * Must have own installation tools. * Reliable, efficient and good attention to detail. * Work alongside our existing team. Date: Saturday, 24 October 2026 Duration: 8 hours (one full day) Location: Glen Osmond, SA Budget is for one day’s labour, not completion of the entire kitchen. Additional work may be available by agreement. Please provide details of your previous installation experience and confirm your availability.

Needing door fitted flush also silver sheet cut to size to put on out side have everything needed also needing carpentry done replace 3 posts and beam where wood has rotted needing your tools and props for verandah to hold up while swapping the posts I have photo of everything for the job

I'm looking for a quote for installation only. I will supply the cabinets. Scope of work: - Upper cabinet run: 3.5 m total - Shelf: 2 m - Small laundry unit: 1.3 m wide - Overhead fridge cabinet: 1.3 m wide - Shallow area: 800 mm wide x 260 mm deep, with 1 base cabinet and 1 upper cabinet to be installed Could you please send me fix price.

need to install two cabinet doors on my kitchen island. I already have the doors and hinges, but the holes need to be drilled and the doors fitted. I’m looking for someone who has the proper tools and experience to complete the installation.

Industrial pipe shelves to put into brick carefully wnd long term stability. Must be experienced. Exact shelves like pictured. But in the loungeroom either side lf the artwork.

Pine wood dresser, make in to vanity, need one of the drawer shorter for plumbing. Watertight.

I have few wall panels and floating shelves which need to be installed. I have all the shelves and panels here at home just need someone to fix them as I could not cut the panel using my saw at home. So need someone to cut it for me , just the height everything else is okay. Also need to install a tv. I have the brackets with me.

I have two IKEA cabinets that need to be built into the spaces they currently sit. The need a top and sides to appear as if they are built-ins. Painter is coming on Monday so I need done ASAP.

Replace wooden carport post and paint

Looking to replace broken board at wood floor

Cut holes in two table for our team to install 2 x Executive Boardroom Table Power Boxes. Cut holes in kitchen cabinetry for our team to install ventilation grills Must be dressed in a plain polo, long pants, and steel-capped boots as you will be working alongside our team and representing our company.

o enlarge the fridge cavity in the kitchen cabinet.

Kitchen cabinet door hinges needs adjusting. Nothing is broken, just hinge adjustment so the doors can close properly

4 Timbers need to be screwed on the back (each as, just follow the instructions), and 2 vents need to be swapped around on most the inside (3 screws in each vent). All material and screws are there