Find a professional local car service in QLD

​Hi, my battery is flat in an underground car park in Underwood. ​Car Model: 2024 Toyota Corolla Cross Hybrid ​Location: Underground car park (Underwood QLD 4119) ​Requirement: Portable jump starter pack. ​Status: The battery is flat (dash/lights flickering, but won't start). ​Looking for someone who can pop in and help jump start it today. Thank you!

So my friends 2012 Audi a5 convertible has a power steering code and to turn the wheel it’s very hard, she got a new battery for her car as it needed one anyways but apparently they have to be coded to the car and it needs a scanner that can do that🤷🏼‍♀️ like a snap on scanner or something not your normal obd2 scanner it has to be able to do Audis, so we need that done for the battery and to read the power steering code to know what exactly needs to be fixed

We are looking at a Honda accord 2009 in Burpengary tomorrow Sunday at 4.30pm. Hoping someone can check out if it’s ok

Looking for an experienced mobile mechanic or broken-bolt extraction specialist to remove a snapped thermostat housing bolt from a 2007 Suzuki Liana 1.8L. One mounting bolt is intact, but the other has snapped off flush. Access is tight, and we’re hoping someone has the specialist tools, such as a compact right-angle drill or bolt extractor, to remove it without having to remove the entire intake manifold.

I have a 2021 Honda NBox Custom JF4. I purchased a set of Cusco Front Side Power Braces. These: cusco part: 3C6 492 FS. Purchased from https://www.go-parts.com.au/products/cusco-front-side-power-brace-for-honda-n-box-jf3-jf4-3c6-492-fs?srsltid=AU7gw4U1xPxnzouginvRgV4y3atzDYhOx1isDTPIuOwDokOUf7veKzpg Key Installation Points (from product notes and owner reports) • Difficulty: Beginner-friendly bolt-on. • Time: ~30 minutes if jacked up properly (per instructions); 1–1.5 hours with ramps or limited access. Some complete it in under an hour. • Tools: • Car ramps (common and effective) or floor jack + jack stands for safe underbody access. • Socket set (14 mm common; 12 mm long socket helpful for some nuts). • Torque wrench (strongly recommended). • Basic tools for bending the included jig if needed. • Preparation: • Bend the included straight “fixing jig” (固定ジグ / nut-stay style bracket) to match the photos in the instruction sheet before starting. • Remove any standard plates or heat-isolating plates as required for access (noted in product listings). You will need to have the tools

2014 Ford Fiesta - overheating. Suspected cylinder head gasket failure resulting in combustion gases entering the cooling system and causing overheating. Further testing is required to confirm the cause. * Carry out a chemical combustion gas (block) test on the cooling system to confirm or rule out head gasket failure. * Perform further cooling system pressure testing if required. Need this sorted urgently. Please advise cost to perform the above testing, and rough estimate on how much you’d charge to fix it.

It seems I have an Estima with headlights where the ballast is a problem, I need someone who can either replace the headlights complete or do an LED conversion for me

My car won't start (likely start motor issue) and would like to have some professional help replacing the starter motor. I can obtain a working starter motor by myself. I also have roadside assistance that can tow my car to you at your convenience. Please leave an offer if you are open to assisting, thank you!

Autoelectrics. 2018 Jeep Cherokee front passenger (left hand side) door; no electronics work; mirror, indicator, lock and window. There seems to be an issue with wires breaking, so need diagnosis and repair. Require quote - have put in $10 because I don't know what a reasonable price would be. Thank you.

The drivers window in my 2001 Mazda 626 has had the regulator bust and the window is all the way down. I cannot work out how to close it. I’ve already taken the door card off. $50 to whoever can close it for me until I can sort a new regulator.

Starter motor needs replacing. I have it jacked wheel off and all but one nut off and have the part ready to go. Struggling to get the final nut off as there is very limited space. Ford ranger px2 2018 wildtrak

2010 Ford Territory - requires fitting new (in box) front passenger window actuator and chassis. I'e replaced switch panel in drivers door already. I'm partially disabled and a senior. Should take less than an hour.

I need the spark plugs replaced in my 2014 Hyundai i20. I have purchased them, I just need a reliable mechanic to install them

I have a Hyundai Tucson and a set of Rhino rack roof bars specified for that vehicle. I am looking for somebody with the required knowledge and experience to fit them for me.

Need roof rack and radio installed, roof rack is assembled and half of cars roof has been pulled free ready for installation

Install two towing mirrors to replace originals on a mazda bt 50

Volvo v40 D4 Oil overfilled - NEEDS TO BE CHECHED AND DRAINED. Need done ASAP please!! 🙏🏼 Location Main Beach / (can drive somewhere close eg. Southport)

Hi, needing a roadworthy done for my car, date still to be confirmed, but hoping by end of week. For a Nissan X trail 2010 model.

Fit rear brake pads to Mazda 6 GH 2008 (hatch)

Need rewiring. Has new main loom and new blinker and tail light assemblies. Wires are there..needs hooking up