Find a local Tasker to inspect your Mazda in VIC

Hard wired installation of Navman MiVue™ True 4K PRO Surround dash cam in Mazda 6 2004 car

I have a light bar requiring fitting to mazda 6. I have wiring harness, light and number plate bracket

Brake Fluid Flush & Bleed – 2011 Mazda 3 (Water Contamination) I accidentally added water to the brake fluid reservoir on my 2011 Mazda 3. The car was driven approximately 560 metres home before I realised, and it has been parked for the last 4–5 days. It is currently not being driven. I’m looking for an experienced mechanic to: * Perform a complete brake fluid flush. * Bleed all four brakes with fresh brake fluid. * Check for any air or water contamination in the brake system. * Inspect the master cylinder and ABS system if required. * Investigate a noise that started after the short drive if it remains after the flush. Please bring all required tools and brake fluid. Experience with brake systems is preferred. Please let me know: * Your experience with this type of job. * Whether you can complete the flush on-site. * Your total price (including brake fluid). Thanks!

Mazda 3 2022 repair required. Please check photos. Check car physical as well - parked in Epping/wollert. Can’t bring to your garage- car is working

Mazda 323 1993 with no spark. I have tested and replaced the Ignition Module as this was the part that has failed previously, no help I have replaced the Ignition coil. I have swapped a spark plug I have tested the crank angle sensor ohms and it seems within normal range. I am not sure how else to diagnose fault at this point and need help to figure it out.

Mazda 3 rear passenger window replacement Window ✅ Door card off ✅ To much headache for me ✅

Providing and replacing the driver’s side mirror, as it appears to be a convex mirror causing objects to appear excessively zoomed out.

Need Auto Electrician / Mazda Specialist – Diagnose TCM Communication Fault (Mazda 3 2010) I have a 2010 Mazda 3 (2.0L automatic) with the engine warning light and traction/slippery light illuminated. A diagnostic scan was performed and shows the following fault codes: - U0101 – Lost Communication with TCM (Transmission Control Module) - Fault present in multiple modules including PCM, ABS, Instrument Cluster, and BCM. - Additional code: U3003:16-08 – Battery Voltage. A mechanic suggested the ECU may need replacement, but I would like a second opinion and proper diagnosis before replacing any major components. What I need: - Full diagnosis of the fault. - Check battery condition and charging system. - Check TCM power supply, fuses, wiring, and connectors. - Confirm whether the issue is the TCM, ECU, wiring, battery, or something else. - Provide repair quote if the fault can be identified. Vehicle: - Mazda 3 / Axela - 2010 - 2.0L Automatic - Located in Melbourne Please respond with your experience working on Mazda electrical or transmission communication faults and your availability. Diagnostic report available upon request.

Hey mate, I have a 2013 Mazda 6 Looking to get a quote to replace front door speakers + change head unit for apple car play happy to purchase the head unit / speaker first, let me know suggestions

Looking for an experienced panel beater or paintless dent repair specialist to repair damage on my 2023 Mazda 6 (Grey Metallic) front bumper. Damage includes: * Dent on the lower front bumper lip (front right side) * Light scratches/scuff marks on the bumper * Small scratches near the black trim section * No cracks or broken parts * Bumper is still securely attached Requirements: * Looking for a professional finish with the paint matched to the original Mazda colour. * Mobile service preferred, but I can travel within Melbourne if required. * Please provide a quote and estimated repair time.

I need someone to bend or pin back the wheel liner of my car, as it’s catching on the coil spring.

Dented passenger door, need repairing

Need a qualified or experienced mechanic to replace rear brake pads on a Mazda CX-5. • ✅ Parts already supplied • 🔧 Labour only required • 📍 Location: Yarraville • ⏱️ Timing: Within the next hour (urgent job) • 🚗 Vehicle is ready to go Should be a straightforward job for someone who knows what they’re doing. Please bring your own tools. Prefer someone with experience in brake work.

My Mazda 6 sedan (2012 model) has a sticky top dashboard due to sun exposure, and I need it replaced. I already have the replacement dashboard, so I only require labour. I’m looking for an experienced panel beater who knows how to carry out this job. There are clear installation videos available on YouTube, and someone skilled in this type of work should be able to complete it in about an hour and half. Task involved: Removal of the sticky passenger‑side top dashboard and installation of the new dashboard. Experienced panel beaters, please get in touch. Thank you.

I’ve purchased the monitor and reverse camera already, just need someone to install the camera. Happy to install the monitor myself as it seems pretty simple. Car is a 2008 Mazda 3 hatchback. Can do it at home in Pakenham or where I work in Notting Hill.

My car needs ac regas Mazda 2 2007 I did ac compressor

2011 Mazda 3 Neo (BL) – Head Unit, Reverse Camera & Front/Rear Dashcam Install - Non-Bose / non-amplified car model. - Preferred install date: 23 Feb onwards (flexible if needed) Parts Supplied by me: • Pioneer DMH-AP6650BT — Head unit • Aerpro AKMZ4 — Fascia kit • Aerpro APP8PIO9 — Pioneer harness • Pioneer RCAMAVIC — Reverse camera • Viofo A229 Plus — Front & rear dashcam • Viofo HK4 (USB-C) — Hardwire kit SCOPE: Head Unit: • Install using supplied fascia & harness • Retain steering wheel controls • Route USB into centre console (secured, not loose) • Mount microphone near rear-view mirror or high on A-pillar Reverse Camera: • Mount centred above number plate • Wire reverse trigger correctly (auto-switch in reverse) Dashcams: • Front camera high centre behind rear-view mirror • Rear camera high centre on rear glass • Hardwire using supplied HK4 via fuse tap (ignition/ACC preferred) • Concealed wiring, no loose trim Clean, factory-style install with everything functioning correctly. Please confirm any: • Experience with Mazda 3 BL installs • Workmanship warranty (if offered) • Availability from 23 Feb onwards Budget set, open to discussion based on experience and quality

Looking to do logbook service, need to be done from home, have plenty of room in garage.

Need a RH side mirror and LH front headlamp assembly installed on a Mazda 3 2014 model. The front bumper assembly is damaged and might need minor adjustment post replacement of the headlamp Replacement parts are available.Happy to lend a hand.

Hi I just need help to replace a inner tierod/rackend passenger side on a 2009 Mazda 3. I've got the parts and wheel will be off. It's a 30 my n job, I don't have the removal tool, or I would do it myself. I'm in Notch Road, Sunbury. Thanks