Find skilled builders in North East Melbourne

Just needing a fence along my driveway, currently have crushed rock on the property line.

Remove approximately 81m2 of clear lightweight pergola roof sheets

Hi all Looking for those with experience in constructing/putting together heavy duty motorised louvred pergola, recently purchased from a company called Outmos on an existing deck. This will also then be approved by a building surveyor post construction to meet planning permit requirements. Most likely will need two people, and I can provide support too as the dimensions are 3m wide x 6m long, using four posts. I will have reinforced areas of the deck for each of the posts as per engineering requirements, and one post will sit off the deck on a poured concrete foundation. Additional building materials if needed will be supplied, so just labour. I can provide Outmos instructions and further engineering documents for further context.

I would like to help you again

The Pergola will extend out from the sliding doors to the end of the pergola. My measurements are 5 .2 L X 2.8 W x 2.4 H approx. there is decking already down which is only 4 years old so its in very good condition. The decking sits on a slab of concrete,

Build Attached Pergola - Epping VIC Hi Taskers, Need a licensed builder/handyman to construct a simple 3m x 3m pergola attached to the back of my house. The area is already fully concreted and level - no slab work needed. • Attach to existing house wall (brick exterior). • Timber or aluminium frame preferred, open roof style for shade. • Include gutters for rain runoff. • Must be council-compliant (Whittlesea LGA, no overlays). • Budget: 1500 (fixed price preferred). • Start ASAP, weekends ok. House is 4 bed/2 bath on 350sqm lot. Photos of site available onsite. Located Epping, near Harvest Home Rd. Please quote with timeline, materials list, and experience examples. Note:- Licensed/insured only

assemble a pergola in back yard

Need a shed installed, i am looking to buy a shed kit from best sheds 7m x 4m x 2.7m gable roof with roller door. There is already a concrete slab and it needs to go hard up to a fence, need someone to look at area in person before i purchase shed.

SUPPLY & INSTAL PERGOLA FLASHING

I would like an Absco garden shed be installed into my backyard. The concrete slap is already there. I just need someone to come over before before end of tomorrow. Just install it. Thank you.

Repaint drive way & alfresco of house around 55 square metre total.

Assemble and place 2.08m x 0.97m Wheelie Bin EasyShed

Need shade cloth and tarp (already purchased) installed to already built pergola.

Installation of a 3m x 3m EasyShed garden shed on a concrete slab

Hi i need this bbq pulled apart and the rendered bricks knocked down. There is a skip on site allready

Need quotes to get driveway concrete repaired. we have an existing concrete crossover. One for the concret blocks roughly 1.5 to 2 mtrs by 1 mtr is damaged and needs replaced. A second block is comparatively less damaged and needs repair or may be replaced.

Need Shed ZINC15081SECOK - Absco Sheds 1.52 x 0.78 x 1.95m Zincalume Zinc Single Door Garden Shed With Anchors to be assembled. Assembly video reference - https://youtu.be/pFyqDm3i44Q?si=RIax-a6xKfItgpz2

Assembly and installation of shed

Bike shed in a flat pack to be assembled.

I’ve attempted to install a Milkcan clothesline on my sloping concrete driveway, but I’m struggling to get the post level both ways without using packers that end up showing and making it look really bad. I’d rather have someone professional do it so it looks perfect. • Clothesline posts need to be cut down so the final installed height is approx. recommended height is 1,800mm, but I want • Posts must be securely fixed to the concrete using the supplied mounting plates. • Driveway is on a slope, so everything needs to be leveled properly for a neat finish. Alignment to the roller door needs to look square if you look down it. I’ve already drilled 4 holes for the first plate and put a few screws in so it needs to be fiddled with. Additional Note: I’ve already drilled one hole, but it’s 12mm when it should have been 10mm. The end of a bolt has dropped into that hole. You’ll need a strong magnet (which you can bring) to fish it out. After that, the hole will need to be neatly fixed—either gluing a bolt in place or another suitable method. What’s Provided: • Clothesline, mounting plates, bolts, and standard accessories. What You Need to Bring: • Tools for concrete drilling/fixing • Saw/grinder for trimming posts to the right height • Strong magnet for retrieving the bolt • Any adhesive or filler needed to repair the oversized hole Level to make it square and aligned