Find a professional pergola installation expert in NSW

Need an insulated pergola/patio for our single storey house in Liverpool. Dimensions are 7m x 4m. Height should be 3m (flyover pergola roof). With provisions for 6 downlights and a ceiling fan which we will connect ourselves.

Build 2.8m x 2.8m Timber Pergola (Gables) Looking for a qualified carpenter or experienced structural landscaper to build a freestanding timber pergola at my property in Gables. Specifications: Dimensions: 2.8m (W) x 2.8m (D) x 2.4m (H). Materials: All H3 Treated Pine. Posts are to be 112x112mm GL8 Primed. Roof: Black weld mesh sheets to be installed on top to act as a trellis for a grape vine. Structural: The structure must be built to support the weight of a mature vine. I require all main beam-to-post connections to be made with M12 galvanised bolts (no simple nailing/screwing of main frame). Footings: 4x galvanised stirrups to be set in concrete. Finish: All cut ends must be treated with preservative (Enseal).

I have a hail stormed damaged pergola, and would like to change the entire pergola.

I’m looking for a handyman to: * Supply and replace my existing pergola roof sheets with polycarbonate sheets (minimum 0.8mm thickness). * Supply and replace two battens that are partially rotten. * Provide all necessary materials, including screws, fixings. The pergola area is approximately 5.3 m × 5 m. Please provide a quotation including materials (sheet style, thickness, and fixings) if the uploaded photos are clear enough. Otherwise, I’d prefer a site visit to provide a more accurate quote. Address can be provided upon request.

The belt on the gear has rolled over and now jammed. Opposite side of the gear, the roller has pulled away from adjusted position. In order to get the belt back on the gear, need to take down front part of awning to get to the gear, untangle the belt, put belt back to correct position and adjust the roller on the opposite side to right tension. Thanks 🛠️ Airtasker Job Post — Motorised Pergola Repair (Russell Lea) Task: Repair motorised louvre pergola (jammed + uneven blades) Location: Russell Lea, NSW Timing: ASAP (today/tomorrow preferred) Budget: Open to quotes Description: My motorised louvre pergola has become jammed while partially open. The blades are not rotating together, and a few appear misaligned or stuck, suggesting a pivot arm or linkage issue rather than a motor failure. The motor still attempts to run, but the blades don’t move properly. Looking for someone experienced with motorised louvre roofs, Vergola-style systems, pivot mechanisms, or opening‑roof repairs. What’s needed: • Inspect and diagnose the mechanical fault • Realign/repair pivot arms or linkage • Check motor + gearbox • Restore smooth open/close operation Please comment with your experience and availability. --- Photo 1 C “Pergola blades stuck mid‑rotation — system jammed and not opening/closing.” Photo 2 Caption: “Uneven blade alignment — likely pivot arm or linkage issue.” Photo 3 Caption: “Close‑up of jammed louvre section — blades not rotating together.” The belt on the gear has rolled over and now jammed. Opposite side of the gear, the roller has pulled away from adjusted position. In order to get the belt back on the gear, need to take down front part of awning to get to the gear, untangle the belt, put belt back to correct position and adjust the roller on the opposite side to right tension. Thanks

We require a survey of a single South Western boundary to determine setbacks for pergola assembly

Build and supply of a 4.5 x 5m insulated flyover pergola.

10 out of my 12 down lights are not working. I would like them fixed please

Need to remove old colorbond and timber. Need new timber and colorbond. The mud room needs an extension roof to put a screen door.

Floors need to be tiled or epoxied. I need all materials and labour included in the job. Pergola size is 4880mm x 3750mm

Looking for someone to paint the timber beams and frame of my outdoor patio/pergola. Paint will be supplied. Only the timber beams and structure need painting — not the polycarbonate roof sheets. The patio runs along the house and has multiple beams/rafters (see photos). Work is overhead so ladder access will be required. Scope: • Paint all timber beams and supports • Careful cutting around the polycarbonate roofing panels • Ideally 2 coats depending on coverage Area will be cleared before work.

Re-fix 3.5 metre x 4 cm X 4 cm hardwood purlin to pergola, with stainless steel screws, old screws broken, check screws on others.

Painting woodwork under the pergola area. Corrugated roofing is due to be upgraded so painting the beams does not need to be accurate as paint on the roof does not matter at this stage. Paint will be provided. Last guy was totally unreliable and did not show up multiple times and with no notice. We are looking for someone who can reliably complete this job.

Install a DIY Aluminum metal pergola (Miami curved pergola from exterior Life). The pergola has 2 posts, both of which slide into metal sleeves that have already been installed into concrete footing. No dyna bolt to concrete floor to fix post required. Fix post to steel sleeve using M12 bolt. All material is DIY, standard lengths, and standard screws/ bolts supplied. See pics. exteriorlife.com.au/how-to/#miami-install

Install gazebo pergola on slap concrete It’s martinekz brand

roof downpipe drain directly on top of pergola roof and causing water to leak at wall edges, Need to connect the down pipe to the pergola gutter through another pipe.

Hi everyone, I need 2x pergolas to be cut back to reduce length by 30cm. 1 has colorbond roof 1 has polycarbonate.

Helper required to install pergola

A very small and light weight pergola that needs to be tipped. Would take 2 minutes to remove. Roof already removed.

Pergola installation..give me a hand for a day, it would be great if you have experience installing pergolas. 450