Find skilled builders in North East Melbourne

half finished pergola (5.6m L x 5.3 w) covering, need 2-3 rafters (timbers ) installed on top of pergola for the fall, then 8 roofsheets/laserlite (these are 6.0m so need installed then cut back to 5.6m which is length of pergola - all timber and roofing screws and laserlite supplied, just need skilled carpenter or handyman to install. even has stringline for fall of roofhseets still there (see pics), shouldnt take too long to finish off.

I would like an Absco garden shed be installed into my backyard. The concrete slap is already there. I just need someone to come over before before end of tomorrow. Just install it. Thank you.

I need a handyman carpenter who can put create a wardrobe

Build Attached Pergola - Epping VIC Hi Taskers, Need a licensed builder/handyman to construct a simple 3m x 3m pergola attached to the back of my house. The area is already fully concreted and level - no slab work needed. • Attach to existing house wall (brick exterior). • Timber or aluminium frame preferred, open roof style for shade. • Include gutters for rain runoff. • Must be council-compliant (Whittlesea LGA, no overlays). • Budget: 1500 (fixed price preferred). • Start ASAP, weekends ok. House is 4 bed/2 bath on 350sqm lot. Photos of site available onsite. Located Epping, near Harvest Home Rd. Please quote with timeline, materials list, and experience examples. Note:- Licensed/insured only

Get a council permit for grape wine pergola. Whittlesea council. 10.8 m long. 4 posts ( 90 x 90 ) with 2.1 meter height. Fix to retaining wall or floor with concrete. L shaped. 1.2 m wide. Around idea and photo of the area attached.

assemble a pergola in back yard

Need a shed installed, i am looking to buy a shed kit from best sheds 7m x 4m x 2.7m gable roof with roller door. There is already a concrete slab and it needs to go hard up to a fence, need someone to look at area in person before i purchase shed.

SUPPLY & INSTAL PERGOLA FLASHING

We are looking for someone either a plumber or someone with a plumbing background to help restore water flow to ice plunge. The water appears to move too slowly perhaps due to a blockage of some sort or which causes clean water to become too warm, too stationary and unclean too quickly. Pressure is in all hoses but not enough. We have refilled, changed pressure of hoses with knobs and cleaned air filter of chiller all with no real improvements. We are hoping that someone can come in and take a section or two apart and determine problem and hopefully minimal or no emptying of plunge can be achieved when done. Can get person started and offer assistance if required. Perfect situation minor issue or blockage removed, plunge is restored to normal flow and plunge becomes cold again as it runs efficiently from chiller again. Kind regards, Dave Gym on Grimshaw 24/7

I am wanting to get quotes on the following job before purchasing this 4x3 pergola. Attached is my backyard pics + pergola inspo. Prepare and pour 4 concrete footings for pergola installation. Some pavers may need to be lifted or artificial turf cut and reinstated. Footings must be level and positioned to pergola specs. Experience with pergola footings required.

Repaint drive way & alfresco of house around 55 square metre total.

Assemble and place 2.08m x 0.97m Wheelie Bin EasyShed

Need shade cloth and tarp (already purchased) installed to already built pergola.

Installation of a 3m x 3m EasyShed garden shed on a concrete slab

Hi i need this bbq pulled apart and the rendered bricks knocked down. There is a skip on site allready

Need quotes to get driveway concrete repaired. we have an existing concrete crossover. One for the concret blocks roughly 1.5 to 2 mtrs by 1 mtr is damaged and needs replaced. A second block is comparatively less damaged and needs repair or may be replaced.

Need Shed ZINC15081SECOK - Absco Sheds 1.52 x 0.78 x 1.95m Zincalume Zinc Single Door Garden Shed With Anchors to be assembled. Assembly video reference - https://youtu.be/pFyqDm3i44Q?si=RIax-a6xKfItgpz2

Assembly and installation of shed

Bike shed in a flat pack to be assembled.

I’ve attempted to install a Milkcan clothesline on my sloping concrete driveway, but I’m struggling to get the post level both ways without using packers that end up showing and making it look really bad. I’d rather have someone professional do it so it looks perfect. • Clothesline posts need to be cut down so the final installed height is approx. recommended height is 1,800mm, but I want • Posts must be securely fixed to the concrete using the supplied mounting plates. • Driveway is on a slope, so everything needs to be leveled properly for a neat finish. Alignment to the roller door needs to look square if you look down it. I’ve already drilled 4 holes for the first plate and put a few screws in so it needs to be fiddled with. Additional Note: I’ve already drilled one hole, but it’s 12mm when it should have been 10mm. The end of a bolt has dropped into that hole. You’ll need a strong magnet (which you can bring) to fish it out. After that, the hole will need to be neatly fixed—either gluing a bolt in place or another suitable method. What’s Provided: • Clothesline, mounting plates, bolts, and standard accessories. What You Need to Bring: • Tools for concrete drilling/fixing • Saw/grinder for trimming posts to the right height • Strong magnet for retrieving the bolt • Any adhesive or filler needed to repair the oversized hole Level to make it square and aligned