Find skilled builders in East Melbourne

Easy shed brand ENSL-S2308 2.25* 0.78*1.98m With Assembly instructions

2 pairs patio doors. Dry rot at bottom of one of each pair. Possible whole door panel replacement. Size: 2190 x 880mm approx.

Existing Condition - Existing drainage channel length approx. 3860mm - Channel width approx. 250mm - Existing drain cut already in place - Bottom of existing grate approx. 200mm below driveway surface - Estimated overall depth approx. 260mm+ (to be confirmed onsite) - Existing channel is not fully concrete-encased at base - Only minor concrete repair expected (no major driveway demolition required) Scope of Work 1. Removal - Remove and dispose of existing drainage channel and grate - Clean and prepare existing drain cut - Minor concrete trimming if required - Remove debris off-site 2. Supply & Installation Supply and install: Heavy-duty driveway drainage system such as: Everhard DuraDRAIN 200 Series Channel & Galvanised Steel Class B Grate (or equivalent heavy-duty system suitable for residential vehicle traffic) Installation requirements: - Confirm dimensions onsite before installation - Ensure correct fall towards existing stormwater outlet - Connect to existing stormwater system (if there is any) - Provide adequate bedding/base support to prevent settlement under vehicle load - Use sand/cement or concrete support where required - Set grate flush with driveway surface - Reinstate minor surrounding concrete neatly 3. Compliance - Suitable for residential vehicle traffic - Installation to good trade practice and Australian standards - Ensure proper drainage performance (no ponding) 4. Warranty Minimum 12-month workmanship warranty

Supply and install shed approx 78 by 156 by 185h cm including concrete floor

Finish painting the pergola. I have paint and brushes, a roller for pergola. Feel free to bring your own tools. 1 coat needed only.

To install a 2.5x1.5m shed from easyshed on the concrete floor with concrete fixings.

Small leak in pergola. Need to fix that and also clean pergola and its gutters. Also check previously fixed two holes.

shed installation (2.25*2.25m)

Paint pergola 3 coats. Will supply paint.

Hi, I need professional help to fix the bottom of my driveway because my car is scraping on the tile edge. What needs to be done: 1. Remove the existing 30cm grey tile strip at the bottom of the driveway 2. Re-build a smooth transition ramp between driveway and footpath 3. Ramp must be: • Strong enough for vehicle weight (Tesla Model Y) • Not too steep • Durable for outdoor / rain 4. I prefer the finish to match the existing driveway, which is dark grey exposed aggregate, but I’m open to options. Your solution may include: • Re-pouring concrete with correct angle • Colour-matching the concrete to dark grey • Re-doing exposed aggregate to match the driveway (ideal) • Any professional suggestion to avoid scraping

2 sides with 3.4m width and one side with length 3.6m. Sides pergola length is 2.3m, but to extend 1.1m to the wall.

1. Garden Bed & Tree Removal Remove trees, shrubs, and garden scrub from six garden beds, including major root systems (not surface cuts only). Dimensions and locations are shown in the attached photos: Garden beds range from approx. 2m–4m long and 0.5m–1.0m wide, with specific beds identified for removal, and some nearby trees clearly marked as not to be removed. • All vegetation will be poisoned prior to job to assist removal. • Soil to be left reasonably level after root removal. • Take care to avoid trees marked “not to be removed”. 2. Garden Path & Area Clean-Up • Remove weeds and shrubs from garden pathways (three main paths). • Clean up one car parking spot area. • Remove and dispose of pot plants in these areas. • Pot plants may be kept by the Airtasker (can be sold for profit) or disposed of in the skip. 3. Demolition Works • Pull down and remove basic cubby house. • Demolish non-functional brick BBQ (sledgehammer likely required). • Bricks may be kept by Airtasker (can be sold for profit) or disposed of in skip. 4. Waste Management • All waste to be placed in a Bunnings Skip (1,000kg capacity). • Skip must be towed to local Waste Facility (approx. 1km away). • Airtasker must supply vehicle with tow bar (if you are unable to provide vehicle for towing – please say so and we can provide, however, you will be responsible for commuting to waste facility and loading / unloading skip). • Skip hire and waste disposal costs are paid separately and are not included in your quote. What You’ll Need • Own tools (e.g. chainsaw, shovel, sledgehammer, pruning tools). • Vehicle with tow bar (unless stated that you would like us to provide). • Experience with garden clearance and demolition preferred. • Able to handle physical outdoor work and heavy lifting. Additional Notes • Photos and videos are attached for accurate quoting. • Job may suit 1–2 people depending on experience. • Timing is flexible and can be agreed.

shed installation for new shed

Needing magnolias and low grass shrubs trimmed back trimmed back from driveway. Down the length of left side and the smaller section at top of driveway on right hand side. Professional gardeners only please. Type of gardening: Hedge trimming Size of garden: Under 50m² Has green waste bin: Yes

I have a narrow shed Size: 2.25m x 0.78m x 1.98m All wall and roof panels are assembled as per manual already and ready to fix I need someone to help me to fix (screw) wall, roof and sliding door. I have all nuts supplied. 5pm onwards preferred

Absco shed assembly - see box and dimensions in photo below.

Recently had delivery of a Absco Garden shed and need someone to assemble and dyna bolt to existing concrete slab. Size is 2.26mt x 0.78mt x 1.95mt. Need assembly done in the next few days.

Repair concrete cracks on mistic joints & surfaces.

We have an outdoor shed (metal sheeting) measuring 3m wide x 0.78m x 1.7m high (brand Easyshed). It has been assembled, but the walls need to be erected. This is likely a two person job or else 1 person who is skilled at holding the walls to drill them together with nails. It should be a straightforward job IF you have experience at assembly or are a skilled tradesperson. Please don’t apply if you don’t have this direct experience - we have been stuffed around before on this task and just need to get the job done. Thank you.

We have a DIY kit of the Pergolux S2 pergola - freestanding 4 x 4 including LED lights. Requires two people. We'd like to see some quotes on assembling this. Assembly instructions can be found here: https://pergolux.au/products/pergolux-sundream-2 There's an installation video here https://www.youtube.com/watch?v=-U-8eDPl_rs Full tools and requirements can be found in the installation guide, but you will need a screw drivers, mallet, level, pliers, caulking gun (with appropriate weatherproof sealant), Allen keys, drill, tape measure, ladder. will need to be secured with appropriate anchors into limestone pavers which have been laid on a concrete slab. The cost of extra anchors etc, we can pay for. Location is shown in the images. Thanks