Find skilled builders in QLD

I purchased a shed from Easyshed and need assistance with assembling it. The size is 1.51 m × 0.78 m × 1.82 m.

Assemble a umbra Stratco shed

Cementing a small area besides the drive way. Dimensions are provided in the image. Area 1: 312 cm x 600 cms Area 210 cm x 260 cms. Areas 1 and 2 touch each other. Areas are sloping a bit . Finish rough and grey to match with driveway.

Cut and dig out approx. 4000mm x 300mm of asphalt driveway using your own machinery

Need existing driveway section lifted and new concrete laid so car can get in driveway

Assemble garden shed. Remove old rivets and install panels as shown in the photo. Bring your tools, drills and drills bit etc.

We are considering purchasing a flatpack garden shed. 6m x 2.25m x 2.35m Tall. Easyshed brand Workshop Shed. Will need someone to assemble it for us on our concrete slab in our backyard. We will remove the existing shed prior to assembly. We require someone experienced & confident in this type/brand of shed assembly as the kit does not come with any pre-drilled holes

Exposing aggregate concrete 70 sq driveway / level up / foot path removal Please give quote

Driveway is being repainted and the grass/soil needs to be removed along the edges to expose the side of the slab. I've hurt my back and need someone to complete prior to work start. Scope: -Remove and retain turf where possible - stack nearby. -Excavate trench along slab approx 20cm wide x 10cm deep to expose side of driveway slab - Soil can be left next to trench -ensure sides of slab are visible for the entire length of slab Total length of trenching is by estimate 25metres, approx 15m of this is grass the remainder is soil/garden bed or already exposed. Soil is combination sandy/clean top soil. Can provide, shovel, trenching shovel, pick as required. Total work estimation 1.5 - 2.0hrs.

Acid wash and seal new concrete driveway. Approx 130sqm

Looking for a structural engineer to help create all the structural engineering docs for a raised 15sqm deck. These docs will be for submission to a private certifier for approval.

Chasing someone to come and sand back our driveway gate. I can supply orbital sander and sandpaper. Just need someone willing to stand there for an hour or so and get it done. Ideally this afternoon - Monday 10/11 in Currimundi

Need someone with a hammer drill and 12mm bit to put 6 screws in kerb to install rubber driveway ramps. There are pre-drilled holes in the rubber ramp.

Scope of Works: – Demolish and remove both the front and rear fences – Total length: approximately 20 linear metres – Clear and dispose of all materials off-site

Assemble shed 3x1.5mt easy sheds.

We are looking for demolition and removal of all blocks down to retaining wall around 3 mtrs long. It should include clean up along retaining wall and clean areas so there is no rough pieces of concrete sticking up from wall.

I need sensor spotlight replaced with security camera sensor spotlight I have camera ready to go Also maybe other work to right tasker

Putting together Stratco flat pack pool pump shed. See video for guide (link below). https://youtu.be/I6ZxP8vYm4A?si=IdpY2HE6bUztba8I

Build and install 3m x 0.78m easyshed shed on already prepared slab. Attach to concrete with concrete fixings (supplied).

We live in a Queensland with a built-in lower level. We want to knock out one existing stud wall (marked red on photos) and expand that small bedroom by having a new stud wall built (marked green on photos). New wall length will be 2.50m, height 1.98m. Between two concrete pillars. Thinking it may be possible to move and re-use existing sliding door. Open to suggestions to minimise work required on ceiling (the two halves of new room have existing good ceilings). Looking for someone experienced to come out, assess what's required and help us decide a plan.