Find a professional bricklayer in QLD

Brick these in - door area/finish one area started (photo 1 and 2) Sliding door bricked up to a window size (size of window will be roughly 2100H 2400W) Property currently vacant so can start asap

Garden walls 500mm high around garden edging

Our pool builder cut into an existing retaining wall to install the pool, leaving a small section open where the blockwork needs reinstating. Looking for an experienced landscaper or bricklayer to rebuild this section of block retaining wall over the top of the existing pipes (see photo) and refit the tile capping on top, butting up against the pool wall. I have kept the original blocks and capping tile for reuse, but you'll need to supply all mortar, adhesive and any other materials required other than blocks/tiles - therefore please factor that in in your price.

We have installed outdoor blinds for this client and the installer has damaged the brickwork, I need the blinds to be removed and the brickwork to be repaired or replaced, up to your discretion what the best method proceeding is

Need a hand finishing off a job

After a quote 450 × 450 × 1800H Coastal Shoreline brick piers × 6 + cap ＋ white mortar ＋ 600H triple-brick low wall + soldier course ＋ black vertical aluminium slats，no visible outer frame ＋ sliding driveway gate

There is a garage wall which needs to be rebuilt and we need to have a support for it as it’s like structural wall.

External brick wall. 6m x 2m high single bricked using double bricks. Footings already done. 3 piers needed. Will need to drill in starter bars. To match already existing boundary wall

We’ve just closed in a sliding door and needing to get a brick layer to lay bricks in between our wooden feature and the window. I have bricks as per picture. Bricks will obviously have to be cut to fit the person doing the job. Must provide everything other than the bricks.

I have a broken brick near the bottom of my front door- see photos. It needs to be replaced. The step tile above is now loose too.

Looking for who can drill four holes in a solid brick wall?112 mm

We have a back-to-wall Easyshed partially assembled. Sides and roof are completed. We need the front panel & door assembled and a notch to be cut from the line of bricks that sticks out from the wall so the shed can sit flush. Location the shed will be positioned attached. Seeking someone that's experienced with Easysheds, is a registered business and has appropriate insurance. Keen to complete this one asap.

Need assistance with brickwork for our seat bench in our garden. We have all the bricks, need them to be laid in the pattern as per picture attached. The total number of courses will be less 2. Concrete slab already in place. I can provide mortar if you advise how much needed etc., or you can include in an off-white light-coloured mortar. If on Saturday or Sunday, I can assist as labourer.

Laying approx 75 x 100 series blocks. I have the blocks and sand. I’ll be here to mix and cut blocks. The wall is only 1200 high.

Replace 5 bricks. Bricks are provided. Mortar should be as close as possible to rest of the wall.

As the title mentions I’m looking for a compound bricklayer to fill in some brickwork to cover up a previous doorway. I don’t have the bricks on site however this can be arranged. Also the bricks do not need to match the existing ones . If you have any questions, let me know

I bought some retaining wall bricks for the yard and they were the wrong size (as shown in the photos) on the left side. Rather than replacing them I just need to move about 15 of them from behind the shed (shown in the photos) over to the area behind the pool to sensor the sizes all match. Just had surgery so I am unable to do it myself.

I removed my Wall Reverse Cycle Air Con a few days ago. I would require a bricklayer to patch up the exterior hole (see photo). Hole at a height of around 4 to 4.5 m - scaffold required. Rough hole dimensions 500 x 400 mm. Please ensure that the brick is cut such that it flows seamlessly when looking from the outside (i.e. bricks bonded in). I will supply the bricks, so just need your help for installation. No requirement to do the interior wall - already done. Start date next Tuesday 9 June.

Bricklaying - besser block wall - 3 courses (600mm high). Non-retaining wall. Just for providing base for non-structural walls. Approx length total of U shaped wall: 19m Core filled, chem set on slab. Please advise if you can also do external waterproofing. We can source all materials.

Chisel out and put fresh mortar in bricks that have movement as pictured