Find a professional staining service in East Melbourne

Sand and polish ~90m² Victorian Ash floors, 3 coats satin (attached), and rubbish removal. Please quote.

Water stain on ceiling. Could you provide a quote on the onsite inspection ?

We have recently ripped up carpet. We want to sand and polish the bare floorboards in living area and hallway, with a subtle, natural stain to match other areas of house. Approx 20sqm. We also want to discuss re-polishing the small kitchen area too. Please note: - please bring all materials and clean up dust before polishing - needs minimum 3 coats of water-based polyurethane (including primer) - no stairs, easy access

We have recently ripped up carpet. We want to sand and polish the bare floorboards in living area and hallway, with a subtle, natural stain to match other areas of house. Approx 20sqm. We also want to discuss re-polishing the small kitchen area too. Please note: - please bring all materials and clean up dust before polishing - needs minimum 3 coats of water-based polyurethane (including primer) - no stairs, easy access

3-5 planks replacement on the decking, oil stain + make good

We want to build a custom multi-level stainless steel bench at a specific size to make the most of an available space inside our shop. Dimensions of the bench are attached in the image. It includes shelves of enclosed drawers and 4 other open shelves.

1. Cut one of our stainless steel benches approx. 5-10cm so it fits inbetween our appliance and another bench. 2. Add a splashback on an existing bench (approx. 1.8m) I've attached images for reference.

We have recently got a deck built on our side yard. We will buy the stain from Bunnings. We require someone to apply the stain for us. The area for decking is roughly 2.37 m x 1.05 m. 2.37 being the longest edge.

Hi, I’m looking for an experienced handyman/stainless steel installer to supply and install a stainless steel sheet on top of my existing countertop. Bench size is 3230mm (L) x 601mm (W). Stainless steel needs to be cut to size and installed neatly with a clean professional and folded edges. There’re 2 be cut-outs required for power point/plug opening (can confirm onsite). Need Up-stand/back splash (like 50–100mm up the wall) Please quote including supply + labour.

18 month old external stairs. Timber balustrade and timber handrail require sanding and re-staining. Main set of stairs going up 1 storey (see photos) plus a second small 3 step stairs outside laundry. The main set of stairs face the sun and timber sustained a lot more wear and tear. The steps are made of steel, so the job is only for the balustrade and handrail. Please see photos.

Sand and Stain Deck about 4.5 m by 5.5 m plus a corner about 2 m by 3.5 m Some nails popped up - please replace with screws Sand and Stain outdoor furniture Fix outdoor staircase as shown

Initial consultation to review the ceiling and determine if anything can be done to lighten the wood and remove the orange tones. Price would then be agreed on. Ceiling is slanted, height is approx 2.5m at lowest and 5m at highest point

Our large William Russell front door (1200x2340mm) needs light sanding and restaining due to UV damage from western sun. The difficulty is it’s two tone vic ash and jarrah veneer, so it requires careful application. The part on right should ideally match the frame colour and the left should only get a non yellowing clearcoat. The indoor side is a much closer match to frame but also browned over time. Prefer someone who has done a door like this before.

Remove stains that are embedded in floor boards and fix furniture scratches

Timber decking requiring surface preparation and staining or oiling. Approximately 32 m².

The wooden floor was stained by unknown ink and need to remove it. Also, so rubbing marking need to be fixed

We have a double sliding (timber) door that needs to be sanding and restaining.

Looking for an experienced concreter to grind, stain, and seal approximately 35sqm of existing concrete flooring in one room. Scope of work: - Grind existing concrete surface. - Apply concrete stain (colour to be discussed). - Seal with a basic satin finish. If possible, install a transition strip to neatly separate the concrete area from the adjoining carpeted section. Additional details: Indoor job. Access is straightforward. Must supply own tools and materials (unless otherwise discussed). Previous experience with decorative concrete preferred — photos of past work welcome. Timing: Ideally completed by 26th February, but happy to negotiate the date for the right person :) Attached are photos of the room - the carpet will be removed and room cleared out before the job begins to ensure there is enough space to work :) Please include your experience, availability, and a rough quote when applying. Thanks so much!

Area 1 DECK Strip, sand, stain main deck including 130mm side panel Approx 35sqm DECK STAIRS Strip, sand, stain stairs - 8 stairs, approx 2sqm including 100mm up stand DECK POSTS Japanese maple stain Strip, filler, sand, fill screw holes on stringers, stain 2.5m x 110 x 110 - 2 posts 1.5m x 110 x 120 - 1 post 3m x 130 x 130 - 1 post Japanese maple stair stringer fascia 2m x 270m Area 2 Back stairs landing - strip, sand, stain ~ approx 1.2sqm including 130mm side panels Stairs - strip, sand, paint in black ~ 5.5sqm 900 x 380 stairs x 25 Stair stringer fascia sand, fill screw holes, paint black Timber balustrade sand, fill screw holes, paint black Work to include: Full strip and sanding of existing coatings on deck boards, stairs, balustrades and posts; prime bare timber; fill screw holes properly; apply quality exterior stain/oil on deck boards; apply durable exterior coating on stairs and balustrade; supply all materials; tidy up.

Sand and stain floorboards