Find a PVC pipe repair professional in NSW

The location is Pindimar NOT Lake Mcquire. Looking for a handy man about 6hr each day, over 2 consecutive days (Saturday and Sunday) to help run, join and secure 2 rows of PVC pipe. From one building, along a 6 m deck and down to a dwellings. It is just a 2 man job because too fiddly on his own. Also to assist with building some outside stairs. Work would be in about 3 weeks time. But that can be negotiated. Need someone that has good handyman skills and about to think outside the box if needed.

Cut a small arch shape in the bottom of a PVC pipe

Looking for an experienced licensed plumber to dig two shallow trenches and lay/connect stormwater PVC pipes to existing kerb outlets on the nature strip. Supply connector and PVC for area in red

Need someone with a core drill to put one hole through a double brick wall (~300mm total depth). ​Hole size: Needs to clear a 115mm OD PVC pipe ( nearest larger core bit is perfect). ​Access: Easy ground level access on both sides, power on site. ​Prep: Work area is cleared with drop sheets down. Wall is clear of services. ​BYO core drill setup / diamond bit. ​Straightforward job for someone with the right gear. Photos attached.

PVC Pipe welding by using heat gun for exhaust system

A plumber is required for correctly connecting a drain pipe to a draining pit See following video link https://drive.google.com/file/u/0/d/1eAzU8e3SLtlxttpoxI7LQK-lI9QDebAu/view?usp=sharing&pli=1

I need help repairing/reconnecting 40mm PVC pool piping. The main issue is a 40mm PVC elbow joint that is partly set into concrete. I’m hoping to salvage/reuse the existing elbow joint rather than cut into the concrete, so the job will likely need a 40mm PVC pipe reamer to clean out the old pipe from inside the elbow joint. I already have the replacement PVC pipe and fittings/materials. Mainly need someone who has the right reamer/tool to clean out the elbow joint. If needed, I’m also happy to pay for you to complete the pipe joints and reconnect everything properly.

PVC pipe attached either side of box guttering, please look at file Must have own workers comp

Lock joint on PVC piping is broken, needs replacement

Stormwater pipe (approximately 2.5 meters in length) needs to be diverted away for ground excavation. Important information: 1. Excavator will be on site and can be used to excavate the pipe. 2. Back Lot access if required. 3. Soil will be removed by owner. 4. Pipe length is approximately 2.5 meters - (only the part highlighted yellow in the picture needs to be moved).

Looking for someone/plumber to replace a sewer PVC pipe which has been squashed due more likely earth movement given no roots were found. See photos. Would also like blue metal to be installed under/around for additional support.

The pvc piping under the sink has a small dripping leak due to the installation of a new sink and movement of the piping. Needs to be fixed. Also to switch around the water lines to the tap from cold to hot and hot to cold. To fix an error when installing the new tap. Easy access as the cupboards have still to be installed. Plenty of parking available. Estimated 30 minute job, we’re super flexible on time to fit into your busy day.

Repair the stormwater pipe leak

Needing the drain line replaced as there is a leak from the elbow joint near the wall and sink where the connection is when the aircon is turned on. It will require: - Drain Pipe - PVC Glue - Cutters - Elbow Joints

Fix leak inside wall and outside on joint of pvc hot water pipe.

I'm doing a laundry reno and I need someone to cap some water taps that are embedded in the cabinet, make sure it is simple to install a tap back on in the future P.S. it's extra work but if you can also cap off an electrical socket that would be great! if not it's all good. I'm negotiable on quotes.

Broken 100 MM PVC sewer pipe. mounted under slab at 1.5 meter High. the damage is to around a 2 meters and a 45 degree elbow. also must redo around 5 saddles along the 15 meter pipe run. Must use Galvanised heavy duty saddles.

I have a blockage in the 40mm suction line of the pool. Distance from skimmer to pump is about 8m. Need someone with a fancy inspection camera to have a look and see what the devil is in there. We have already tried with a rigid seasnake but it couldn't get past the first bend the camera head kept hitting the bend. Possibly with the right skid it might make the turn. You can park about 12m away in the rear laneway so very easy access. The pipe isnt new. It was an existing pool that got drained and retired. So the pipe was fine to pump out prior to retiling. Also I have inspected the first bend at each end. Nothing there. So blockage is definitely further along. First job is just to find the blockage. Then once we know what it is we can work out the next step.

Connect the PVC pipes from existing pool heat pump installation

Need to cut out silicon seal which has been poured into downlet pipe to secure washing machine outlet hose at floor level. In awkward position.