Find a local Tasker to inspect your Peugeot in VIC

My Peugeot wagon Won't get out of. Park Has a flat tyre

Repair reverse camera from my 308 Peugeot

I have a 2009 peugeot 308 (2.0 diesel) that has been stalling ( engine cuts off while car is driving) and also stalls while engine is running( but can't accelerate) limp mode? It has been diagnosed by 3 mechanics as being a fuel issue and to get a fuel pressure regulator ( suction control valve) or to buy the whole fuel pump where the regulator is attached Incase it's not just the valve. I need someone to come and install the part but also to help me get it. I've had confusing responses and not much help by the mechanics in finding the suitable part and honestly am not even sure it will fix the issue, it's all become very confusing and frustrating and I need it done ASAP as I have no car for work. I have already replaced the fuel filter and fuel pressure sensor and cannot afford to keep fixing it. Want the cheapest option and sourcing it. Found some on eBay but again not sure they suit, mixed replies. Experience with peugeot is necessary and just need someone to get the job done without fuss. Located Brunswick.

I have both new axles and gearbox seals Car is on private concrete drive I have jacks stands and power

Getting an anti pollution warning and the car is shuddering. Have air filters, spark plugs etc just need someone to fit them

I need a dash camera installed professionally in a 2017 Peugeot 2008. The dash camera is a Navman Auto220

Hi, I need someone with experience in car electrics or convertible repairs to help fix the rear electric window on my Peugeot 306 Cabriolet model 2001. The rear window is not working, it doesn’t go up or down when using the switch. I’m not sure if it’s a motor issue, wiring, or the switch itself. I’m based in St Kilda, but I can also drive to you if that’s more convenient. Flexible with time but would like it done ASAP.

I have a timing issue/ misfires. Need timing chain replaced on Peugeot 308 model. I have the new timing chain and need a qualified mechanic that has worked on Peugeot cars to do the job either onsite or their workshop within a reasonable distance.

Oil in water, car overheats, need to understand the problems and fix

Car has oil in water and is overheating. I'd like a diagnosis

Car is leaking coolant, engine warning light is on, overheating and oil in water. Timing chain may also need to be fixed.

I changed the clutch and having problems with programming it Renault master 2013 x62 frontwheel drive. Sequential automatic geatbox 6speed

Hi, I have an old car Peugeot 308 SW 2010, I need to get my car windows tinted, thanks, cheers

Thermostat has been replaced, coolant has been flushed when run OBD Scanner faults come up -- Codes : P0599 Thermostat Control - Short Circuit to Battery P0118 - Coolant Temperature sensor signal -- Short Circuit to positive or open circuit I need auto electrician. Please if you are not expert in Auto electrical issues, please do not contact me. Thanks

I can bring the car to your garage.

Need a new windscreen installed. 2014 Peugeot 208 gti

Mistakenly put too much engine oil in car, need someone with the right tools and experience to drain it to appropriate level. Car hasn't been driven since oil was put in. Car is a Peugeot 207 and is located at residence in Essendon (on the street in front of house) Not desperate to get it done but the sooner the better.

Car: Peugeot 207 made in 2010 Car hasn't been driven since November due to auto electrical issues and now the battery has died. Please send me quotes for the battery to be replaced.

Mechanic Must be familiar with PEUGEOT 308 diesel.and must have the Peugeot diagnostic tester tool Following is repair work done. But still NO GO MECH 1. Replaced timing belt & injectors. Electronic boards checked OK MECH 2. Replaced Fuel filter & Camshaft sensor AND Compression OK Motor turns over but doesn’t start

Towbar wiring as installed for a 2006 Peugeot 407 HDI wagon . This system has never worked properly. I need someone good with auto electrics to see whether you can get the current wiring working or bypass it and fit a new system.