Find a professional pergola installation expert in NSW

Need to do painting of timber pergola and oiling and painting of decking

Looking for someone to paint the timber beams and frame of my outdoor patio/pergola. Paint will be supplied. Only the timber beams and structure need painting — not the polycarbonate roof sheets. The patio runs along the house and has multiple beams/rafters (see photos). Work is overhead so ladder access will be required. Scope: • Paint all timber beams and supports • Careful cutting around the polycarbonate roofing panels • Ideally 2 coats depending on coverage Area will be cleared before work.

I need the trunk of a large fan palm sawn back and the dead frongs on it removed. I need a gas bottle bracket attached to the external brick wall of my house. I need the painting of the frame of pergola finished off. I started it the uprights are done and some of the cross beams.

Floors need to be tiled or epoxied. I need materials and labour included in the job

We need 3 non motorised blinds installed in our outdoor Pergola. They are a custom fit, we will provide the blinds but the installer will have to use additional aluminium cladding to correct one blinds as not installed perpendicularly in a small angle. https://youtu.be/5zgEr5dcjxY Install instructions above.

I got the material ready. Just need your professional experience to clean and stain the deck. Thanks

Re-fix 3.5 metre x 4 cm X 4 cm hardwood purlin to pergola, with stainless steel screws, old screws broken, check screws on others.

secure 5 posts into concrete slab. Attach four beams professionally.

Painting woodwork under the pergola area. Corrugated roofing is due to be upgraded so painting the beams does not need to be accurate as paint on the roof does not matter at this stage. Paint will be provided. Last guy was totally unreliable and did not show up multiple times and with no notice. We are looking for someone who can reliably complete this job.

Install a DIY Aluminum metal pergola (Miami curved pergola from exterior Life). The pergola has 2 posts, both of which slide into metal sleeves that have already been installed into concrete footing. No dyna bolt to concrete floor to fix post required. Fix post to steel sleeve using M12 bolt. All material is DIY, standard lengths, and standard screws/ bolts supplied. See pics. exteriorlife.com.au/how-to/#miami-install

Install gazebo pergola on slap concrete It’s martinekz brand

roof downpipe drain directly on top of pergola roof and causing water to leak at wall edges, Need to connect the down pipe to the pergola gutter through another pipe.

Hi everyone, I need 2x pergolas to be cut back to reduce length by 30cm. 1 has colorbond roof 1 has polycarbonate.

Helper required to install pergola

A very small and light weight pergola that needs to be tipped. Would take 2 minutes to remove. Roof already removed.

Pergola installation..give me a hand for a day, it would be great if you have experience installing pergolas. 450

1. Cut existing concrete slab/ tiles 2. Dig and install high strength concrete footing for 2 pergola posts: 1000Wx1000Lx900D 3. Concrete supplied

Pergola needs Colourbond flashing installed, Flashing already purchased and marked up Access: no access to neighbour property, must be installed from on top of pergola (pergola roof mix of colourbond corregated & skylight corrugation) all sections marked cut/fit required on one 1.5m section near lobby Need to supply monument colour tech screws

I would like to build a timber rectangle pergola 5m long 3m wide Posts will be bolted to the concrete slab

Have a pergola about 12m long. Need 3 - 4 batten lights connected to middle pergola beam. Also need 1 or 2 flood lights connected against pergola to face yard. Have an existing hard wire with some length about 5 metres as a start. May also need to divert a plug point to BBq area counter or against screening post if its possible and meets regulations. Needed by Monday 22nd or latest latest 23rd Tuesday. Thanks.