Find a professional gate installation in Greenvale VIC

I have an existing 1.2m-high blade fence and want to add one more 2.2m-wide fence panel. The remaining space of approximately 5.3m will be for a manual sliding gate. I already have all the materials, including the fence panel, sliding gate and flanged posts. The existing mailbox will be removed, and a new mailbox will need to be installed into the fence by cutting a square opening. I just need someone to install the posts, fence panel, sliding gate and track, secure everything with bolts, and install the new mailbox. You’ll need to bring a grinder and the necessary tools for the installation.

Have an exisiting blade fence 1.2m high but want to add 1 more panel 2.2m then the rest of the space around 5.3m will be a sliding gate manual, I have everything you just need a grinder to cut the gate and the bolts, the post I have are flanged posts mailbox will be removed and I’ll have one here you’ll need to install in the fence cut a square and install it

Have an exisiting blade fence 1.2m high but want to add 1 more panel 2.2m then the rest of the space around 5.3m will be a sliding gate manual, I have everything you just need a grinder to cut the gate and the bolts, the post I have are flanged posts

Side gate is tilting. Need it repaired. If unrepairable, need quote on a new side gate installed.

Side access gate out of alignment and does not close properly. Need fixed so gate can lock into place

I need an electrician to bring electricity from the house to the front gate to add a motor to the gate but there’s currently concrete, so can this be done? How much? As I don’t want to cut concrete, the wall from the house to the front gate it around 3.5-4m please check photo

Need someone with experience, I have currently 2 panel fence which are up and installed but I will be getting 1 more panel 2m and a sliding gate which is around 4.5m long and you will need to install them, if there’s a way to add a motor to make it electric but without having wires exposed I will do that other wise it’ll be manual

I am looking to supply and install a front fence and gates for my corner block property. The fence should be horizontal aluminium slat style in dark charcoal/anthracite colour, 90 cm high along the full front boundary, with a large motorised driveway gate with remote control and a small pedestrian walk-through gate with a chrome handle. Please provide a quote including supply and installation.

Need a gate lock removed, and new one supplied and installed on outside colorbond gate

Replace A concrete slab for a sliding gate motor pad should be at least 100-150mm thick.

the gate doesn't hold up and the latch and the dropstick come off the fence. there is not a deep enough hole for the dropstick, the fence is quite large and the small screws on the latch is not sufficient. i need this gate to be strengthened with a deeper hole drilled into concrete for the pin. steonger latch. the posts strengthened and the fence supported.

My side gate latches onto a post attached to the Hebel wall of the house. It's fixed with two bolts but gets loose over time and have been repaired before. As you know, Hebel walls are not very strong and the gate moves with wind which over the time loosens the post. So, I want someone with expertise to provide a permanent fix to this. See attached pictures. Your offer should include the cost of materials.

Brick pillar has crumbling mortar mostly towards bottom and also at base which I believe is concrete. Overall pillar has leaned in to an angle where it is no longer aligned with sliding gate. Need this removed and crumbling parts either removed and re-mortared or re-bricked whatever is more appropriate. top half still seems quite solid. I have approximately 100 spare bricks not in this pillar that can be used as required however this entire pillar would require more than that amount so probably can't do from scratch without re-using a fair bit from the pillar itself.

I need fencing in my backyard for my dog, the area is approximately 10 metres from the brick to the colour bond fence. It’ll need to have a gate for access and be roughly 2 metres in height

Installation of automatic sliding gate and pedestrian gate

Hi are u cancelling the job we had lined up for the posts and the gate?

My side gate isn’t closing. It’s somehow become unaligned and is catching at the top, preventing it from closing.

Hi need a new black colourbond side gate, if done good and price is right you will also change the side fence that’s 25m long, Measurements for side gate is Side gate/fence 2040 wide total Gate 1.2m wide Height 2.2m

i need a custom aluminium pool gate built and powder coated

We have a colorbond gate to our sideyard and die to heavy winds, the fixed part of the gate is pulled off from its base. It needs to be fixed so we can lock it.