Find experienced local fencing contractors in West Ryde

We just finished building a deck around the pool on fibro cement. Tiles are about to installed so we are about 2 weeks away from install. Total size of the glass pool fence is 17.5m with 2 gates. I need a quote for supply and install. Must have experience in installing glass pool fences

Part of a timber fence in the backyard is tilting. The degree of the tilt shown in the image attached.

Hi, I need an experienced handyman or fencer to help with install green metal gate using existing post + fit MagnaLatch pool safety lock. Ideally, you can utilize, modify, or securely re-fix this existing green post to hang the gate, ensuring it opens and closes properly. • Fixings: Please bring your own heavy-duty hinges (self-closing spring hinges preferred for pool areas) and suitable metal screws/fixings. Requirement: Must be installed in compliance with Australian pool safety standards (correct legal height and self-latching operation). Please reply with your availability and an all-inclusive quote. Thanks!

My fence is wobbly, it doesn’t need to be replaced, just the main posts need to be fixed so it’s straight and in place again, potentially needs a few of the main posts replaced to do this. Total fence line is about 15 metres

Require quote for Labour cost only, for the job described below. All materials (Gate Panels, Stiles, butt hinges, drop bolt etc) will be provided to the contractor EXCEPT for Hex head TEK screws (Woodland Grey) to be provided by the contractor (for mounting / framing the gates). 1.) Install two gates (photo 1) onto the two posts already concreted into the ground (photo 2) 2.) Frame a new gate panel approx 800m wide by 1800 high with Stile (photo 3) & gate rail (to be dismantled from another OLD gate) and then hinge this new gate onto one of the existing gate panels 3.) Install on this new Gate panel - 1x 400mm Drop Bolt and 'gate latches' (to be dismantled from an Old Gate) 4.) Core drill into concrete for three drop bolts (one on each gate) and glue plastic sleeve into concrete hole

The timber fence between two properties is leaning to one property. The elevation of the two properties are not the same (one slightly lower than the other). The base is not secure leading the fence to lean on one side.

Replace wooden Fence ( treated pine ) at front yard , 1.8 m high, demolish and remove old fence.

My fence has almost fallen over. I need someone to prop it up.

I need to repair a brick fence of one meter tall , we are 2 people that can help with the task

Supply and install 23m colourbond fencing (18m high) Previous wooden fence removed already.

supply and install a timber lattice privacy screen to a rear alfresco in between two brick pillars, the floor is tiled - width 3250mm, height 1800mm, opening of lattice can not be more than 30mm

The wooden gate came off from the 2 hinges. I need somebody to help mount the wooden gate back to the wooden post. - Due date: Flexible

around 25m and includding some gates

install a picket fence at the front of a block after old one has been removed, various sections in between brickwork and in ground between two properties.

The end of the fence was knocked down by an oversize van in my driveway

Need knocked over driveway fence repair. Licensed and bonded. - Due date: Flexible

Can I please request a quote for a paling fence in Denistone? 3.6metres in length and the height of the palings is 165cm above ground level. A small gate is needed too to access the passageway. In addition, repair of some older palings. - Due date: Flexible

Install glass fence and gate - Due date: Needs to be done on Saturday, 13 May 2023

Boundary fencing with timber or colorbond - Due date: Flexible

Scope of Works: 1. Supply and install small wooden picket gate (pathway) - Width (including posts) – 1000 mm - Height – 750mm minimum - With latch and lockable - Wall is newly constructed, post required - Material - Timber preferred, painted white 2. Supply and install long wooden picket gate (driveway) - Width (including posts) – 3000 mm (single gate) - Height – 550mm minimum - With latch and lockable - Wall is newly constructed, post required - Material - Timber preferred, painted white 3. Repair existing round top wooden gate - Each gate dimensions 1600mm wide, 1800 mm tall (approx.) - Assess condition to determine if gate can be repaired or needs to be replaced - One existing large gate has come off its hinges - One post needs replacing - New fittings required (latch, hinges, lock etc) 4. Install mailbox X2 - Install 2 X mailboxes (supplied) on wall The quote is for including Materials. Materials for the gate will be agreed after discussion. Note: all dimensions are approximate Please message for any further information if needed. Thanks - Due date: Before Wednesday, 29 March 2023